2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Operate the cooler compressor under the conditions shown below:

    Item
    Condition
    Engine Speed
    Idling
    Operating Time
    3 minutes or more
    A/C Switch Status
    On
    Blower Switch Status
    HI
    Set Temperature
    MAX COOL
    This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

    NOTICE:
    It is not necessary to operate the cooler compressor if the A/C does not operate because of compressor lock, etc.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.

    HINT:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.


2. REMOVE FRONT SEAT ASSEMBLY
  1. for Manual Seat:
    Remove the front seat assembly (Click here).

  1. for Power Seat:
    Remove the front seat assembly (Click here).

  1. for Walk in Seat Type:
    Remove the front seat assembly (Click here).


3. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY

  1. E283079
    Detach the 4 clips.

  1. Disconnect the connector and remove the integration control and panel assembly.


4. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

B356216
  1. Detach the 4 clips and remove the instrument panel finish panel end LH.


5. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

B356215
  1. Detach the 5 clips and remove the No. 2 instrument panel finish panel cushion.


6. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

HINT:
Use the same procedure described for the No. 2 instrument panel finish panel cushion.


7. REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION

HINT:
Use the same procedure described for the No. 2 instrument panel finish panel cushion.


8. REMOVE FRONT CONSOLE UPPER PANEL GARNISH (for Manual Transmission)

  1. w/o Seat Heater System:

    1. B357641E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.

    3. Disconnect the connector.

  1. w/o Seat Heater System:

    1. B357639E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.

    3. Disconnect each connector.

  1. w/ Climate Control Seat System:

    1. B357646E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.

    3. Disconnect each connector.


9. REMOVE FRONT CONSOLE UPPER PANEL GARNISH (for Automatic Transmission)

  1. w/o Seat Heater System:

    1. B357641E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.

    3. Disconnect the connector.

  1. w/o CRAWL:

    1. B357639E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.

    3. Disconnect each connector.

  1. w/ CRAWL:

    1. B357640E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.


10. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

B356218
  1. for LHD:

    1. Remove the screw.

    2. Detach the 2 clips and 2 guides and remove the No. 1 instrument panel under cover.

    3. Disconnect each connector.

  1. B298554
    for RHD:

    1. Remove the screw.

    2. Detach the 3 clips and 2 guides and remove the No. 1 instrument panel under cover.

    3. Disconnect each connector.


11. REMOVE FRONT NO. 1 CONSOLE BOX INSERT

B238139
  1. Detach the 2 clips and guide and remove the front No. 1 console box insert.


12. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Remove the screw.

  1. Detach the 3 clips and 2 guides and remove the No. 2 instrument panel under cover.

    B298555E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


13. REMOVE FRONT NO. 2 CONSOLE BOX INSERT

B238145
  1. Detach the 2 clips and guide and remove the front No. 2 console box insert.


14. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
  1. for Automatic Transmission:
    Remove the shift lever knob sub-assembly (Click here).

  1. for Manual Transmission:
    Remove the shift lever knob sub-assembly (Click here).


15. REMOVE CONSOLE PANEL SUB-ASSEMBLY
  1. for Automatic Transmission:
    Remove the console panel sub-assembly (Click here).

  1. for Manual Transmission:
    Remove the console panel sub-assembly (Click here).


16. REMOVE NO. 1 CONSOLE BOX DUCT (for Single Air Conditioning System)

B363311
  1. Remove the clip and No. 1 console box duct.


17. REMOVE COOLING BOX TRAY
  1. Remove the cooling box tray.


18. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY

  1. E197111
    Detach the 8 claws.

  1. Disconnect the connector and remove the rear console end panel sub-assembly.


19. REMOVE CENTER FLOOR CARPET COVER RH

  1. E199752E01
    Detach the 3 claws and remove the center floor carpet cover RH.
    Text in Illustration 
    *1
    Fastener


20. REMOVE CONSOLE BOX ASSEMBLY

B363313
  1. Remove the clip.

  1. Remove the 7 bolts and 2 screws.

  1. Remove the 2 bolts and disconnect the 2 cooler pipes.

  1. Disconnect the drain cooler hose.

  1. Disconnect the connector and remove the console box assembly.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →