2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. INSPECT 1ST GEAR THRUST CLEARANCE

  1. C238808
    Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.20 to 0.45 mm (0.00787 to 0.0177 in.)

    1. If the clearance is not as specified, replace the No. 1 synchronizer ring set.


2. INSPECT 2ND GEAR THRUST CLEARANCE

  1. C238809
    Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.00394 to 0.00984 in.)

    1. If the clearance is not as specified, replace the No. 1 synchronizer ring set.


3. INSPECT 3RD GEAR THRUST CLEARANCE

  1. D026045E01
    Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.00394 to 0.00984 in.)

    1. If the clearance is not as specified, replace the No. 2 synchronizer ring set.


4. INSPECT 1ST GEAR RADIAL CLEARANCE

  1. D026047E01
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.020 to 0.073 mm (0.000785 to 0.00287 in.)

    1. If the clearance is not as specified, replace the 1st gear needle roller bearing with a new one.


5. INSPECT 2ND GEAR RADIAL CLEARANCE

  1. D026048E01
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    1. If the clearance is not as specified, replace the 2nd gear needle roller bearing with a new one.


6. INSPECT 3RD GEAR RADIAL CLEARANCE

  1. D026049E01
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    1. If the clearance is not as specified, replace the 3rd gear needle roller bearing with a new one.


7. REMOVE 1ST GEAR

  1. C216007E01
    Using SST and a press, remove the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.
    SST
    09950-00020  


8. REMOVE NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

  1. C216216
    Remove the synchronizer rings from the output shaft.


9. REMOVE 1ST GEAR THRUST WASHER PIN
  1. Remove the thrust washer pin from the output shaft.


10. REMOVE 1ST GEAR NEEDLE ROLLER BEARING
  1. Remove the needle roller bearing from the output shaft.


11. REMOVE 1ST GEAR BEARING SPACER
  1. Remove the bearing spacer from the output shaft.


12. REMOVE BEARING SHAFT SNAP RING

  1. D026055E01
    Using 2 screwdrivers and a hammer, tap off the snap ring from the output shaft.

    NOTICE:
    Use a piece of cloth to prevent the snap ring from flying off.


13. REMOVE 2ND GEAR

  1. C216008E01
    Using SST and a press, remove the No. 1 transmission clutch hub with the reverse gear, the No. 1 synchronizer ring set and the 2nd gear from the output shaft.
    SST
    09950-00020  


14. REMOVE 2ND GEAR NEEDLE ROLLER BEARING
  1. Remove the needle roller bearing from the output shaft.


15. REMOVE REVERSE GEAR

  1. D026058E01
    Remove the reverse gear, 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs.

    NOTICE:
    Use a piece of cloth to prevent the shifting keys and shifting key springs from popping out.


16. REMOVE CLUTCH HUB SET SHAFT SNAP RING

  1. D026059E01
    Using a snap ring expander, remove the snap ring from the output shaft.

    NOTICE:
    Do not damage the sliding surface of the bearing.


17. REMOVE 3RD GEAR

  1. C216009E01
    Using SST and a press, remove the No. 2 transmission clutch hub with the No. 2 transmission hub sleeve, the No. 2 synchronizer ring and the 3rd gear from the output shaft.
    SST
    09950-00020  


18. REMOVE 3RD GEAR NEEDLE ROLLER BEARING
  1. Remove the needle roller bearing from the output shaft.


19. REMOVE NO. 2 TRANSMISSION HUB SLEEVE

  1. D033571E01
    Remove the No. 2 hub sleeve, 3 No. 2 synchromesh shifting key springs and 3 No. 2 synchromesh shifting keys from the No. 2 clutch hub.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →