2013-2015 Land Cruiser Prado · Service Manual Drivetrain

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT OUTPUT SHAFT

  1. D029121E01
    Using a dial indicator, measure the output shaft runout.

    Maximum runout:
    0.03 mm (0.00118 in.)

    1. If the runout is more than the maximum, replace the output shaft with a new one.

  1. D029122E01
    Using a micrometer, measure the journal diameter at A, B and C on the output shaft.

    Standard Journal Diameter:
    Item
    Specified Condition
    Journal A
    38.979 to 38.995 mm (1.5346 to 1.5352 in.)
    Journal B
    46.984 to 47.000 mm (1.8498 to 1.8504 in.)
    Journal C
    37.984 to 38.000 mm (1.4954 to 1.4961 in.)

    1. If the diameter is not as specified, replace the output shaft with a new one.

  1. D026065E01
    Using a micrometer, measure the thickness of the output shaft flange as shown in the illustration.

    Standard thickness:
    4.8 to 5.2 mm (0.189 to 0.204 in.)

    1. If the thickness is not as specified, replace the output shaft.


INSPECT 3RD GEAR

  1. D026066E01
    Using a cylinder gauge, measure the inside diameter of the 3rd gear.

    Standard inside diameter:
    44.015 to 44.040 mm (1.7329 to 1.7339 in.)

    Maximum inside diameter:
    44.040 mm (1.7339 in.)

    1. If the inside diameter is more than the maximum, replace the 3rd gear with a new one.


INSPECT 2ND GEAR

  1. D026067E01
    Using a cylinder gauge, measure the inside diameter of the 2nd gear.

    Standard inside diameter:
    53.015 to 53.040 mm (2.0872 to 2.0881 in.)

    Maximum inside diameter:
    53.040 mm (2.0881 in.)

    1. If the inside diameter is more than the maximum, replace the 2nd gear with a new one.


INSPECT 1ST GEAR

  1. D026068E01
    Using a cylinder gauge, measure the inside diameter of the 1st gear.

    Standard inside diameter:
    46.015 to 46.040 mm (1.812 to 1.8126 in.)

    Maximum inside diameter:
    46.040 mm (1.8126 in.)

    1. If the inside diameter is more than the maximum, replace the 1st gear with a new one.


INSPECT 1ST GEAR THRUST WASHER

  1. D026069E01
    Using a micrometer, measure the thickness of the thrust washer.

    Standard thickness:
    5.95 to 6.05 mm (0.235 to 0.238 in.)

    Minimum thickness:
    5.95 mm (0.235 in.)

    1. If the thickness is less than the minimum, replace the 1st gear thrust washer.


INSPECT NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

  1. D029123E01
    Apply gear oil to the cone of the 1st gear, and check that the No. 1 synchronizer ring set does not turn in either direction while pushing the No. 1 synchronizer ring set.
    1. If No. 1 synchronizer ring set turns, replace it.

  1. D029124
    Measure the clearance between the No. 1 synchronizer ring and 1st gear while pushing the No. 1 synchronizer ring against the cone of the 1st gear.

    Standard clearance:
    0.75 to 1.65 mm (0.0295 to 0.0650 in.)

    1. If the clearance is not as specified, replace the No. 1 synchronizer ring with a new one.


INSPECT NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)

  1. D029125E01
    Apply gear oil to the cone of the 2nd gear, and check that No. 1 synchronizer ring set does not turn in either direction while pushing the No. 1 synchronizer ring set.
    1. If No. 1 synchronizer ring set turns, replace it.

  1. D029126E01
    Push the No. 1 synchronizer ring set against the cone of the 2nd gear. Measure the clearance between the No. 1 synchronizer ring set and 2nd gear.

    Standard clearance:
    0.65 to 1.75 mm (0.0256 to 0.0689 in.)

    1. If the clearance is not as specified, replace the No. 1 synchronizer ring with a new one.


INSPECT NO. 2 SYNCHRONIZER RING (for 3rd Gear)

  1. D026074E01
    Apply gear oil to the cone of the 3rd gear, and check that No. 2 synchronizer ring does not turn in either direction while pushing the No. 2 synchronizer ring.
    1. If the No. 2 synchronizer ring turns, replace it.

  1. D026075E01
    Push the No. 2 synchronizer ring against the cone of the 3rd gear. Measure the clearance between the No. 2 synchronizer ring (for the 3rd gear) and 3rd gear.

    Standard clearance:
    0.75 to 1.65 mm (0.0295 to 0.0650 in.)

    1. If the clearance is not as specified, replace the No. 2 synchronizer ring with a new one.


INSPECT REVERSE GEAR

  1. D026076E01
    Using a vernier caliper, measure the groove of the No. 1 shift fork and the thickness of flange of the reverse gear. Then calculate the clearance between the No. 1 shift fork and flange.

    Standard clearance:
    0.15 to 0.41 mm (0.00591 to 0.0161 in.)

    1. If the clearance is not as specified, replace the reverse gear and No. 1 shift fork with new ones.


INSPECT NO. 1 TRANSMISSION CLUTCH HUB

  1. D026077E01
    Check the sliding condition between the No. 1 clutch hub and reverse gear.

  1. Check the spline of the reverse gear for wear.

    1. If there are any defects, replace the No. 1 clutch hub.


INSPECT NO. 2 TRANSMISSION HUB SLEEVE

  1. D026078E01
    Using a vernier caliper, measure the groove of the No. 2 hub sleeve and the thickness of claw of the No. 2 shift fork. Then calculate the clearance between the No. 2 hub sleeve and the claw.

    Standard clearance:
    0.15 to 0.35 mm (0.00591 to 0.0138 in.)

    1. If the clearance is not as specified, replace the No. 2 hub sleeve and No. 2 shift fork with new ones.


INSPECT TRANSMISSION CLUTCH HUB NO. 2

  1. D026079E01
    Check the sliding condition between the No. 2 clutch hub and No. 2 hub sleeve.

  1. Check the splines of the No. 1 clutch hub for wear.

  1. Check the tip of the spline gear sleeve of the reverse gear for wear.

    1. If there are any defects, replace the No. 1 clutch hub or reverse gear.

← DISASSEMBLY (from Aug 2013)REASSEMBLY (from Aug 2013) →