2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. INSTALL NO. 2 TRANSMISSION HUB SLEEVE

  1. D033571E02
    Install the 3 No. 2 synchromesh shifting key springs and 3 synchromesh shifting keys to the No. 2 clutch hub.

    NOTICE:
    Make sure that the No. 2 hub sleeve and No. 2 clutch hub are installed facing the proper directions.

  1. Apply gear oil to the sliding part of the No. 2 hub sleeve, and install it to the No. 2 clutch hub.


2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING

  1. C089845E01
    Apply gear oil to the needle roller bearing and install it to the output shaft.


3. INSTALL 3RD GEAR

  1. D026080E01
    Apply gear oil to the 3rd gear and install it to the output shaft.


4. INSTALL NO. 2 SYNCHRONIZER RING (for 3rd Gear)

  1. D026081E01
    Apply gear oil to the No. 2 synchronizer ring and install it to the 3rd gear.


5. INSTALL NO. 2 TRANSMISSION CLUTCH HUB

  1. D026082E01
    Using SST and a press, install the No. 2 clutch hub to the output shaft.
    SST
    09608-06041  

    NOTICE:
    1. Install the hub while aligning the positions of the shifting keys with the key grooves of the No. 2 synchronizer ring.
    2. Make sure the 3rd gear rotates smoothly.

  1. Select a snap ring that makes the clearance between the No. 2 clutch hub and snap ring within the specification.

    Standard clearance:
    0.10 mm (0.00394 in.) or less

    Snap Ring Thickness:
    Thickness
    1.80 mm (0.0709 in.)
    1.85 mm (0.0728 in.)
    1.90 mm (0.0748 in.)
    1.95 mm (0.0768 in.)
    2.00 mm (0.0787 in.)
    2.05 mm (0.0807 in.)
    2.10 mm (0.0827 in.)

  1. D026059E02
    Using a snap ring expander, install the snap ring.

    NOTICE:
    Do not damage the sliding surface of the bearing.


6. INSTALL 2ND GEAR NEEDLE ROLLER BEARING

  1. C089844E01
    Apply gear oil to the needle roller bearing, and install it to the output shaft.


7. INSTALL 2ND GEAR

  1. D026084E01
    Apply gear oil to the 2nd gear and install it to the output shaft.


8. INSTALL NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)

  1. D029127E01
    Apply gear oil to the No. 1 synchronizer ring set and install it to the 2nd gear.


9. INSTALL REVERSE GEAR

  1. D026083E01
    Using a screwdriver, install the 3 synchromesh shifting key springs and 3 No. 1 synchromesh shifting keys to the No. 1 clutch hub.

  1. Apply gear oil to the reverse gear and install it to the No. 1 clutch hub.


10. INSTALL NO. 1 TRANSMISSION CLUTCH HUB

  1. C216010E01
    Using SST and a press, install the No. 1 clutch hub to the output shaft.
    SST
    09316-60011   (09316-00041)

    NOTICE:
    1. Make sure that the No. 1 synchromesh shifting key positions are aligned with the No. 1 synchronizer ring key grooves.
    2. Make sure the 1st gear rotates freely.

  1. Select a snap ring that makes the thrust clearance between the No. 1 clutch hub and snap ring to be within the specification.

    Standard clearance:
    0.1 mm (0.00394 in.) or less

    NOTICE:
    Do not damage the journal surface of the snap ring.

    Snap Ring Thickness:
    Thickness
    2.30 mm (0.0906 in.)
    2.35 mm (0.0925 in.)
    2.40 mm (0.0945 in.)
    2.45 mm (0.0965 in.)
    2.50 mm (0.0984 in.)
    2.55 mm (0.1004 in.)
    2.60 mm (0.1024 in.)

  1. D026087E01
    Using a brass bar and hammer, tap on the snap ring.


11. INSTALL 1ST GEAR BEARING SPACER

  1. C089843E01
    Apply gear oil to the bearing spacer and install it to the output shaft.


12. INSTALL 1ST GEAR NEEDLE ROLLER BEARING

  1. C089842E02
    Apply gear oil to the needle roller bearing and install it to the output shaft.


13. INSTALL 1ST GEAR THRUST WASHER PIN

  1. D026052E01
    Install the thrust washer pin to the output shaft.


14. INSTALL NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

  1. C216216
    Apply gear oil to the No. 1 synchronizer ring set and install it to the output shaft.


15. INSTALL 1ST GEAR

  1. D026089E01
    Apply gear oil to the 1st gear and install it to the output shaft.


16. INSTALL 1ST GEAR THRUST WASHER

  1. D026090E01
    Apply gear oil to the thrust washer and install it to the output shaft.


17. INSTALL OUTPUT SHAFT CENTER BEARING

  1. D026091E03
    Using SST and a press, install a new center bearing to the output shaft.
    SST
    09316-60011   (09316-00031)

    NOTICE:
    Install the center bearing so that the snap ring groove of the bearing faces the rear side.


18. INSTALL 5TH GEAR

  1. C216011E01
    Using SST and a press, install the 5th gear to the output shaft.
    SST
    09316-60011   (09316-00031)

    NOTICE:
    1. Check that the 5th gear and the splines of the output shaft fit before installing the 5th gear.
    2. Make sure face the convex part of the gear faces the front side.


19. INSPECT 1ST GEAR THRUST CLEARANCE

  1. C238808
    Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.20 to 0.45 mm (0.00787 to 0.0177 in.)

    1. If the clearance is not as specified, replace the No. 1 synchronizer ring set.


20. INSPECT 2ND GEAR THRUST CLEARANCE

  1. C238809
    Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.00394 to 0.00984 in.)

    1. If the clearance is not as specified, replace the No. 1 synchronizer ring set.


21. INSPECT 3RD GEAR THRUST CLEARANCE

  1. D026045E01
    Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.00394 to 0.00984 in.)

    1. If the clearance is not as specified, replace the No. 2 synchronizer ring set.


22. INSPECT 1ST GEAR RADIAL CLEARANCE

  1. D026047E01
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.020 to 0.073 mm (0.000785 to 0.00287 in.)

    1. If the clearance is not as specified, replace the 1st gear needle roller bearing with a new one.


23. INSPECT 2ND GEAR RADIAL CLEARANCE

  1. D026048E01
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    1. If the clearance is not as specified, replace the 2nd gear needle roller bearing with a new one.


24. INSPECT 3RD GEAR RADIAL CLEARANCE

  1. D026049E01
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    1. If the clearance is not as specified, replace the 3rd gear needle roller bearing with a new one.

← INSPECTION (from Aug 2013)COMPONENTS (from Aug 2013) →