INSTALLATION
Removal / installation · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| 1. INSTALL CLEARANCE WARNING ECU ASSEMBLY (for 4 Sensor Type) |
Install the clearance warning ECU assembly with the bolt.
Connect the connector.
| 2. INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY (for 4 Sensor Type) |
Attach the claw to install the connector as shown in the illustration.

- NOTICE:
- Be sure to connect each connector securely.
Attach the 2 claws to lock the connector lock as shown in the illustration.

Attach the claw to connect the connector as shown in the illustration.

- NOTICE:
- Be sure to connect the connector securely.
Install the driver side junction block assembly with the bolt and 2 nuts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the connector labeled (1).

- NOTICE:
- Be sure to connect each connector securely.
Attach the 2 claws to connect the 2 connectors labeled (2) as shown in the illustration.
- NOTICE:
- Be sure to connect each connector securely.
Connect the 3 connectors.
- NOTICE:
- Be sure to connect each connector securely.
| 3. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for 4 Sensor Type) |
Install the lower No. 1 instrument panel airbag assembly with the 4 bolts.
Connect the connector.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 4 Sensor Type) |
Connect each connector and each cable.
Attach the 14 clips to install the lower instrument panel finish panel sub-assembly.
Install the 2 bolts.
Attach the 2 claws to close the cover.
| 5. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for 4 Sensor Type) |
Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.
Install the screw.


Text in Illustration *A
for LHD
*B
for RHD
| 6. INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for 4 Sensor Type) |
Connect each connector.
Attach the 4 clips to install the instrument panel finish plate garnish.
| 7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for 4 Sensor Type) |
Connect each connector.
Attach the 4 clips to install the lower instrument panel finish panel assembly.
| 8. INSTALL INSTRUMENT SIDE PANEL RH (for 4 Sensor Type) |
Attach the 5 clips, claw and 3 guides to install the instrument side panel RH.
| 9. INSTALL COWL SIDE TRIM BOARD RH (for 4 Sensor Type) |
Attach the clip and claw to install the cowl side trim board RH.
Install the clip.
| 10. INSTALL DOOR SCUFF PLATE ASSEMBLY RH (for 4 Sensor Type) |
Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly RH.
| 11. INSTALL CLEARANCE WARNING ECU ASSEMBLY (for 8 Sensor Type) |
Install the clearance warning ECU assembly with the 2 nuts.
Connect the connector.
| 12. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for 8 Sensor Type) |
![]() ![]() |
Connect each connector.
Attach the 5 clips and claw to install the glove compartment door assembly.
Install the 2 bolts and 2 screws.
Text in Illustration *1
Bolt
*2
Screw
| 13. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for 8 Sensor Type) |
Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.
Install the screw.


Text in Illustration *A
for LHD
*B
for RHD
| 14. INSTALL INSTRUMENT PANEL ORNAMENT (for 8 Sensor Type) |
Attach the 5 clips to install the instrument panel ornament.
| 15. INSTALL INSTRUMENT SIDE PANEL LH (for 8 Sensor Type) |
Attach the 5 clips, claw and 3 guides to install the instrument side panel LH.
| 16. INSTALL COWL SIDE TRIM BOARD LH (for 8 Sensor Type) |
Attach the clip and claw to install the cowl side trim board LH.
Install the clip.
| 17. INSTALL DOOR SCUFF PLATE ASSEMBLY LH (for 8 Sensor Type) |
Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly LH.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for 4 Sensor Type) |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 19. CHECK SRS WARNING LIGHT (for 4 Sensor Type) |

