2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL CLEARANCE WARNING ECU ASSEMBLY (for 4 Sensor Type)
  1. Install the clearance warning ECU assembly with the bolt.

  1. Connect the connector.


2. INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY (for 4 Sensor Type)

  1. E178382
    Attach the claw to install the connector as shown in the illustration.

    NOTICE:
    Be sure to connect each connector securely.

  1. E178380
    Attach the 2 claws to lock the connector lock as shown in the illustration.

  1. E178378
    Attach the claw to connect the connector as shown in the illustration.

    NOTICE:
    Be sure to connect the connector securely.

  1. Install the driver side junction block assembly with the bolt and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. E197201E07
    Connect the connector labeled (1).

    NOTICE:
    Be sure to connect each connector securely.

  1. Attach the 2 claws to connect the 2 connectors labeled (2) as shown in the illustration.

    NOTICE:
    Be sure to connect each connector securely.

  1. Connect the 3 connectors.

    NOTICE:
    Be sure to connect each connector securely.


3. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for 4 Sensor Type)
  1. Install the lower No. 1 instrument panel airbag assembly with the 4 bolts.

  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 4 Sensor Type)
  1. Connect each connector and each cable.

  1. Attach the 14 clips to install the lower instrument panel finish panel sub-assembly.

  1. Install the 2 bolts.

  1. Attach the 2 claws to close the cover.


5. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for 4 Sensor Type)
  1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.

  1. Install the screw.

    B298555E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


6. INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for 4 Sensor Type)
  1. Connect each connector.

  1. Attach the 4 clips to install the instrument panel finish plate garnish.


7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for 4 Sensor Type)
  1. Connect each connector.

  1. Attach the 4 clips to install the lower instrument panel finish panel assembly.


8. INSTALL INSTRUMENT SIDE PANEL RH (for 4 Sensor Type)
  1. Attach the 5 clips, claw and 3 guides to install the instrument side panel RH.


9. INSTALL COWL SIDE TRIM BOARD RH (for 4 Sensor Type)
  1. Attach the clip and claw to install the cowl side trim board RH.

  1. Install the clip.


10. INSTALL DOOR SCUFF PLATE ASSEMBLY RH (for 4 Sensor Type)
  1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly RH.


11. INSTALL CLEARANCE WARNING ECU ASSEMBLY (for 8 Sensor Type)
  1. Install the clearance warning ECU assembly with the 2 nuts.

  1. Connect the connector.


12. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for 8 Sensor Type)

B238220E01
  1. Connect each connector.

  1. Attach the 5 clips and claw to install the glove compartment door assembly.

  1. Install the 2 bolts and 2 screws.

    Text in Illustration 
    *1
    Bolt
    *2
    Screw


13. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for 8 Sensor Type)
  1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.

  1. Install the screw.

    B298555E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


14. INSTALL INSTRUMENT PANEL ORNAMENT (for 8 Sensor Type)
  1. Attach the 5 clips to install the instrument panel ornament.


15. INSTALL INSTRUMENT SIDE PANEL LH (for 8 Sensor Type)
  1. Attach the 5 clips, claw and 3 guides to install the instrument side panel LH.


16. INSTALL COWL SIDE TRIM BOARD LH (for 8 Sensor Type)
  1. Attach the clip and claw to install the cowl side trim board LH.

  1. Install the clip.


17. INSTALL DOOR SCUFF PLATE ASSEMBLY LH (for 8 Sensor Type)
  1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly LH.


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for 4 Sensor Type)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


19. CHECK SRS WARNING LIGHT (for 4 Sensor Type)
(Click here)
← INSTALLATION (Aug 2013 – Jul 2014)COMPONENTS (from Aug 2013) →