2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

E200370E01
  1. Put protective tape around the door scuff plate assembly RH.

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate assembly RH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


4. REMOVE COWL SIDE TRIM BOARD RH

E200371
  1. Remove the clip.

  1. Detach the clip and claw and remove the cowl side trim board RH.


5. REMOVE INSTRUMENT SIDE PANEL RH

B238212E01
  1. Put protective tape around the instrument side panel.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 5 clips, claw, and 3 guides.

  1. Disconnect the connector and remove the instrument side panel.


6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

E200373
  1. Detach the 4 clips.

  1. Disconnect each connector and remove the lower instrument panel finish panel assembly.


7. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH

B238239
  1. Detach the 4 clips.

  1. Disconnect each connector and remove the instrument panel finish plate garnish.


8. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.

  1. Install the screw.

    B298555E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

B239280E01
  1. Using a screwdriver, detach the 2 claws and open the cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B243715
    w/o Knee Airbag:

    1. Remove the 2 bolts <C>.

    2. Detach the 7 clips.

    3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

  1. B238216
    w/ Knee Airbag:

    1. Remove the 2 bolts <C>.

    2. Detach the 14 clips.

    3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.


10. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

B362705
  1. Disconnect the connector.

  1. Remove the 4 bolts and lower No. 1 instrument panel airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


11. REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

  1. E197200
    Disconnect the 3 connectors.

  1. E197201E06
    Detach the 2 claws and disconnect the 2 connectors labeled (1) as shown in the illustration.

  1. Disconnect the connector labeled (2).

  1. E197202
    Remove the bolt and 2 nuts and disconnect the driver side junction block assembly.

  1. E178377
    Detach the claw and disconnect the connector as shown in the illustration.

  1. E178379
    Detach the 2 claws and release the connector's lock as shown in the illustration.

  1. E178381
    Detach the claw and disconnect the connector as shown in the illustration.

  1. Remove the driver side junction block assembly.


12. REMOVE PARKING ASSIST ECU

B359152
  1. Disconnect the 3 connectors.

  1. Remove the 2 bolts and parking assist ECU.

← REMOVAL (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →