INSTALLATION
Removal / installation · Vehicles built from Aug 2013
| 1. INSTALL COOLER DRYER |
Using pliers, install the cooler dryer.
Apply a sufficient amount of compressor oil to the contact surfaces of a new O-ring and the cap.

- Compressor:
- ND-OIL 8 or equivalent
Install the O-ring to the cap.
Using a 14 mm socket hexagon wrench, install the cap to the modulator.
- Torque:
- 2.9 N*m{ 30 kgf*cm , 26 in.*lbf }
| 2. INSTALL COOLER CONDENSER ASSEMBLY |
Install the cooler condenser with the 3 bolts as shown in the illustration.

- Torque:
- for bolt A:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
- for bolt B:
- 4.4 N*m{ 44 kgf*cm , 39 in.*lbf }
| 3. CONNECT DISCHARGE HOSE SUB-ASSEMBLY |
Remove the attached vinyl tape from the hose and the connecting part of the cooler condenser.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose joint.
- Compressor:
- ND-OIL 8 or equivalent
Install the O-ring to the discharge hose.
Connect the discharge hose to the cooler condenser with the bolt.
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
- NOTICE:
- When tightening the bolt, do not allow any tools to contact the pipe.
- When tightening the bolt, hold a part of the pipe near the connector.
- When tightening the bolt, do not allow any tools to contact the pipe.
| 4. CONNECT NO. 2 COOLER CONDENSER BRACKET |
Install the 2 bolts and No. 2 cooler condenser bracket.
| 5. CONNECT NO. 1 COOLER CONDENSER BRACKET |
Install the 2 bolts and No. 1 cooler condenser bracket.
| 6. INSTALL AIR CONDITIONING TUBE ASSEMBLY |
Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube assembly joint.
- Compressor:
- ND-OIL 8 or equivalent
Install the O-ring to the air conditioning tube assembly.
Connect the air conditioning tube assembly to the cooler condenser with the bolt.
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
- NOTICE:
- When tightening the bolt, do not allow any tools to contact the pipe.
- When tightening the bolt, hold a part of the pipe near the connector.
- When tightening the bolt, do not allow any tools to contact the pipe.
| 7. CHARGE REFRIGERANT |
- SST
- 09985-20010
(09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).
*1: For vehicles with the 2TR-FE engine which have neither the rear cooler nor cool box, the refrigerant charging amount changes based on region.Standard Model Code
Air Conditioning Type
Cool Box
Refrigerant Charging Amount
Except the model codes below
w/o Rear Cooler
w/ Cool Box
600 +/-30 g (21.2 +/-1.1 oz.)
w/o Cool Box
550 +/-30 g (19.3 +/-1.1 oz.)
w/ Rear Cooler
w/ Cool Box
800 +/-30 g (28.2 +/-1.1 oz.)
w/o Cool Box
770 +/-30 g (27.2 +/-1.1 oz.)
w/ Rear Cooler
for Cold Area Specification Vehicles
w/o Cool Box
720 +/-30 g (25.3 +/-1.1 oz.)
TRJ150L-GKMEKV
TRJ150L-GKPEKV
TRJ155L-GJPEKV
GRJ150L-GKFEKV
GRJ150L-GKAEKV
KDJ150L-GKFEYV
KDJ150L-GKAEYV
w/o Rear Cooler
w/ Cool Box
600 +/-30 g (21.2 +/-1.1 oz.)
w/o Cool Box
550 +/-30 g (19.3 +/-1.1 oz.) or 600 +/-30 g (21.2 +/-1.1 oz.) *1
w/ Rear Cooler
w/ Cool Box
800 +/-30 g (28.2 +/-1.1 oz.)
w/o Cool Box
770 +/-30 g (27.2 +/-1.1 oz.)


- NOTICE:
- Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
- Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.
- Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
| 8. INSTALL RADIATOR ASSEMBLY |
for 1GR-FE:
Install the radiator assembly (Click here).
for 2TR-FE:
Install the radiator assembly (Click here).
for 1KD-FTV, w/ DPF:
Install the radiator assembly (Click here).
for 1KD-FTV, w/o DPF:
Install the radiator assembly (Click here).
for 5L-E:
Install the radiator assembly (Click here).
| 9. ADD ENGINE COOLANT |
for 1GR-FE:
Add engine coolant (Click here).
for 2TR-FE:
Add engine coolant (Click here).
for 1KD-FTV, w/ DPF:
Add engine coolant (Click here).
for 1KD-FTV, w/o DPF:
Add engine coolant (Click here).
for 5L-E:
Add engine coolant (Click here).
| 10. WARM UP ENGINE |
Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.
- NOTICE:
- Be sure to warm up the compressor when turning the A/C switch is on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.
| 11. INSPECT FOR ENGINE COOLANT LEAK |
for 1GR-FE:
Inspect for engine coolant leak (Click here).
for 2TR-FE:
Inspect for engine coolant leak (Click here).
for 1KD-FTV:
Inspect for engine coolant leak (Click here).
for 5L-E:
Inspect for engine coolant leak (Click here).
| 12. CHECK FOR REFRIGERANT GAS LEAK |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation under these conditions:
- Stop the engine.
- Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
- Repeat the test 2 or 3 times.
- Make sure that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).
- Stop the engine.
Using a halogen leak detector, check the refrigerant line for leakage.

Text in Illustration *1
Halogen Leak Detector
*a
Check for Leakage
If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.
