2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. DRAIN ENGINE COOLANT
  1. for 1GR-FE:
    Drain the engine coolant (Click here).

  1. for 2TR-FE:
    Drain the engine coolant (Click here).

  1. for 1KD-FTV, w/ DPF:
    Drain the engine coolant (Click here).

  1. for 1KD-FTV, w/o DPF:
    Drain the engine coolant (Click here).

  1. for 5L-E:
    Drain the engine coolant (Click here).


2. REMOVE RADIATOR ASSEMBLY
  1. for 1GR-FE:
    Remove the radiator assembly (Click here).

  1. for 2TR-FE:
    Remove the radiator assembly (Click here).

  1. for 1KD-FTV, w/ DPF:
    Remove the radiator assembly (Click here).

  1. for 1KD-FTV, w/o DPF:
    Remove the radiator assembly (Click here).

  1. for 5L-E:
    Remove the radiator assembly (Click here).


3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Operate the cooler compressor under the conditions shown below:

    Item
    Condition
    Engine Speed
    Idling
    Operating Time
    3 minutes or more
    A/C Switch Status
    On
    Blower Switch Status
    HI
    Set Temperature
    MAX COOL
    This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

    NOTICE:
    It is not necessary to operate the cooler compressor if the A/C does not operate because of compressor lock, etc.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.

    HINT:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.


4. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

  1. E199365E01
    Remove the bolt and disconnect the discharge hose from the cooler condenser.
    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 2TR-FE
    *C
    for 1KD-FTV, for 5L-E

    NOTICE:
    1. When removing the bolt, do not allow any tools to contact the pipe.
    2. When removing the bolt, hold a part of the pipe near the connector.

  1. Remove the O-ring from the discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.


5. DISCONNECT AIR CONDITIONING TUBE ASSEMBLY

  1. E199366
    Remove the bolt and disconnect the air conditioning tube assembly from the cooler condenser.

    NOTICE:
    1. When removing the bolt, do not allow any tools to contact the pipe.
    2. When removing the bolt, hold a part of the pipe near the connector.

  1. Remove the O-ring from the air conditioning tube assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.


6. DISCONNECT NO. 1 COOLER CONDENSER BRACKET

  1. E199359
    Remove the bolt and disconnect the No. 1 cooler condenser bracket.


7. DISCONNECT NO. 2 COOLER CONDENSER BRACKET

  1. E199360
    Remove the bolt and disconnect the No. 2 cooler condenser bracket.


8. REMOVE COOLER CONDENSER ASSEMBLY

  1. E199367
    Remove the 3 bolts and cooler condenser as shown in the illustration.


9. REMOVE COOLER DRYER

  1. I030086E01
    Using a 14 mm socket hexagon wrench, remove the cap from the modulator.

  1. I032475E01
    Remove the O-ring from the cap.

  1. E050386E01
    Using pliers, remove the cooler dryer.

← ON-VEHICLE INSPECTION (from Aug 2013)INSTALLATION (from Aug 2013) →