2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. INSTALL REAR SEATBACK HEATER ASSEMBLY

B248650E02
  1. Set the rear seatback heater assembly in place with the name stamp side facing the separate type rear seatback cover.

    Text in Illustration 
    *1
    Tack Pin
    *2
    Name Stamp

  1. Install the rear seatback heater assembly with 11 new tack pins.


2. INSTALL SEPARATE TYPE REAR SEATBACK COVER
  1. Set the separate type rear seatback cover in place.

  1. B237678E01
    Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 8 new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the separate type rear seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  1. B248336
    w/ Seat Heater System:

    1. Connect the rear seatback heater assembly wire harness to the separate type rear seatback pad.


3. INSTALL SEATBACK COVER WITH PAD

  1. w/ Seat Heater System:

    1. B360132E01
      Install the wire harness as shown in the illustration.
      Text in Illustration 
      *a
      Paint Mark

  1. B237675
    Connect the outer belt to the seatback cover with pad.

  1. B237674E01
    Attach the hooks.
    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Hook
    *3
    Hog Ring

  1. Using hog ring pliers, install the seatback cover with pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type rear seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.


4. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
  1. Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.


5. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH
  1. Attach the 7 clips to install the rear seatback board carpet assembly LH.


6. INSTALL REAR SEATBACK COVER
  1. Attach the 4 claws to install the rear seatback cover.


7. INSTALL REAR SEAT SHOULDER BELT COVER
  1. Connect the outer belt to the rear seat shoulder belt cover.

  1. B237669
    Attach the 2 guides and 2 claws to install the rear seat shoulder belt cover.


8. INSTALL SEAT BELT ANCHOR COVER CAP

B237667
  1. Attach the 2 claws to install the seat belt anchor cover cap.


9. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

  1. B165026E02
    Connect the cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly LH.

  1. Install the 2 screws.


10. INSTALL RECLINING ADJUSTER KNOB CAP LH

B237664
  1. Attach the guide and claw to install the reclining adjuster knob cap LH.


11. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B242874E01
  1. Install the inner belt and connect the 3 point type belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    Text in Illustration 
    *a
    Protruding Part


12. INSTALL CENTER SEATBACK ASSEMBLY
  1. Install the center seatback assembly with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


13. INSTALL SEAT CUSHION COVER WITH PAD

  1. B237625
    Attach the hook.

  1. B237623
    Attach the hooks to install the seat cushion cover with pad.

  1. w/ Seat Heater System:

    1. B360133
      Pass the wire harness as shown in the illustration.

    2. B359313
      Connect the 2 rear seat heater connectors.


14. INSTALL REAR SEAT CUSHION MOULDING LH

B237620
  1. Move the rear seat cushion moulding LH in the direction of the arrow to attach the guide.

  1. Attach the 3 claws and clip to install the rear seat cushion moulding LH.


15. INSTALL CENTER SEAT HINGE COVER LH

B237618
  1. Attach the 2 guides and install the center seat hinge cover LH with the clip.


16. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
  1. Install the reclining adjuster release handle LH with the 3 screws.


17. INSTALL REAR SEAT UPPER RECLINING COVER LH

B237786
  1. Attach the 3 claws to install the rear seat upper reclining cover LH.


18. INSTALL REAR NO. 1 SEAT ASSEMBLY LH
(Click here)
← INSPECTION (from Aug 2013)COMPONENTS (from Aug 2013) →