2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
(Click here)

2. REMOVE REAR SEAT UPPER RECLINING COVER LH

B237615E01
  1. Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B237616
  1. Remove the 3 screws and reclining adjuster release handle LH.


4. REMOVE CENTER SEAT HINGE COVER LH

B237617
  1. Using a clip remover, remove the clip.

  1. Detach the 2 guides and remove the center seat hinge cover LH.


5. REMOVE REAR SEAT CUSHION MOULDING LH

B237619
  1. Using a clip remover, detach the clip.

  1. Using a moulding remover, detach the 3 claws.

  1. Move the rear seat cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding LH.


6. REMOVE SEAT CUSHION COVER WITH PAD

  1. B359313
    w/ Seat Heater System:

    1. Disconnect the 2 rear seat heater connectors.

    2. B360133
      Pull out the wire harness as shown in the illustration.

  1. B237622
    Detach the hooks.

  1. B237624
    Detach the hook and remove the seat cushion cover with pad.


7. REMOVE CENTER SEATBACK ASSEMBLY

B237629
  1. Remove the 2 bolts and center seatback assembly.


8. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B237670
  1. Remove the bolt and inner belt and disconnect the 3 point type belt anchor.


9. REMOVE RECLINING ADJUSTER KNOB CAP LH

B237663E01
  1. Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


10. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

  1. B237665
    Remove the 2 screws.

  1. B165025E02
    Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly LH.


11. REMOVE SEAT BELT ANCHOR COVER CAP

  1. B237666E01
    Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


12. REMOVE REAR SEAT SHOULDER BELT COVER
  1. Disconnect the outer belt from the rear seat shoulder belt cover.

  1. B360121
    Detach the 2 claws and 2 guides, and then remove the rear seat shoulder belt cover.


13. REMOVE REAR SEATBACK COVER

B237641
  1. Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

    HINT:
    Tape the screwdriver tip before use.


14. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH

B237671
  1. Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly LH.


15. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B237672
  1. Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.


16. REMOVE SEATBACK COVER WITH PAD

  1. B237673E01
    Remove the 10 hog rings and detach the hooks, and then remove the seatback cover with pad.
    Text in Illustration 
    *1
    Hook
    *2
    Hog Ring

  1. B237676
    Disconnect the outer belt from the seatback cover with pad.

  1. w/ Seat Heater System:

    1. B360132
      Remove the wire harness.


17. REMOVE SEPARATE TYPE REAR SEATBACK COVER

  1. B248335
    w/ Seat Heater System:

    1. Disconnect the rear seatback heater assembly wire harness from the separate type rear seatback pad.

  1. B237677
    Remove the 8 hog rings and separate type rear seatback cover from the separate type rear seatback pad.


18. REMOVE REAR SEATBACK HEATER ASSEMBLY

B248650E01
  1. Cut off the 11 tack pins which fasten the rear seatback heater assembly to the separate type rear seatback cover, and then remove the rear seatback heater assembly from the separate type rear seatback cover.

    Text in Illustration 
    *1
    Tack Pin

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →