DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| DATA LIST |
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.
Read the Data List according to the display on the GTS.
Blind Spot Monitor Master Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Main Switch
Blind spot monitor main switch assembly (multi-function switch) / OFF or ON
ON: Blind spot monitor main switch assembly (multi-function switch) on
OFF: Blind spot monitor main switch assembly (multi-function switch) off
-
Warning Indicator Turning on (Master)
State of the outer rear view mirror indicator LH turning on / OFF or ON
- OFF: Any state except "ON" state
- ON: Either of the following state
- During initial check
- Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated
-
Warning Indicator Flashing (Master)
State of the outer rear view mirror indicator LH flashing / OFF or ON
OFF: Any state except "ON" state
ON: Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on
-
Main Switch Indicator Status
State of the blind spot monitor indicator on the blind spot monitor main switch assembly (multi-function switch) / OFF or ON
OFF: Indicator not illuminated
ON: Indicator illuminated
-
Warning Indicator Input Circuit Voltage
Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V
Not illuminated: Below 1 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current
Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA
Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Right Turn SW State (CAN)
State of the headlight dimmer switch assembly (right turn signal light switch) / ON or OFF
ON: Right side of turn signal light switch on
OFF: Right side of turn signal light switch off
-
Left Turn SW State (CAN)
State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF
ON: Left side of turn signal light switch on
OFF: Left side of turn signal light switch off
-
Reverse
State of the shift position R signal / OFF or ON
ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed
Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph)
Vehicle stopped: 0 km/h (0 mph)
-
Steering Angle
Steering sensor / Min.: -3072°, Max.: 3070.5°
Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage
Power supply voltage / Min.: 0 V, Max.: 50 V
11 to 14 V
-
Indicator Light Control State
Outer rear view mirror indicator dimming state / Dim OFF or Dim ON
Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV Flag
Hybrid vehicle / OFF or ON
OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag
VGRS installed / OFF or ON
OFF: VGRS not installed
ON: VGRS installed
-
Main SW Inspection Completeness Flag
Completion of inspection for blind spot monitor main switch assembly (multi-function switch) / Incompl or Compl
Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when the blind spot monitor main switch assembly (multi-function switch) is changed from off to on during Test Mode.
Beam Axis Inspection Completeness Flag
Completion of beam axis inspection / Incompl or Compl
Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Destination Undefined Flag
Destination determination / Unfixed or Fixed
Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Angle Adjustment by Auto Alignment
Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg
Angle adjusted using auto alignment is displayed
When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Setting of Warning Indicator Current (Dim OFF)
Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA
0 to 100 mA
-
Setting of Warning Indicator Current (Dim ON)
Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA
0 to 100 mA
-
Mirror LED Duty Ratio (Blinking)
Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100%
50%
-
Number of DTC
Number of DTC / Min.: 0, Max.: 255
When system is normal: 0
When a malfunction is detected: More than 0
-
Blind Spot Monitor Slave Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Warning Indicator Turning on (Slave)
State of the outer rear view mirror indicator RH turning on / OFF or ON
OFF: Any state except "ON" state
ON: Either of the following state- During initial check
- Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated
-
Warning Indicator Flashing (Slave)
State of the outer rear view mirror indicator RH flashing / OFF or ON
OFF: Any state except "ON" state
ON: Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on
-
Buzzer Sound Status
State of the RCTA buzzer (blind spot monitor buzzer) / OFF or ON
OFF: Buzzer not sounding - ON: All of the following conditions are met:
- Not during initial check
- Vehicle detected in warning area of RCTA
- Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more
- Shift lever in R
- No DTC output
-
Warning Indicator Input Circuit Voltage
Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V
Not illuminated: Below 1 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current
Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA
Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Buzzer Input Circuit Voltage
RCTA buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V
Not sounding buzzer: 11 to 14 V
Sounding buzzer: Alternating between 0 to 14 V
-
Right Turn SW State (CAN)
State of the headlight dimmer switch assembly (right turn signal light switch) / ON or OFF
ON: Right side of turn signal light switch on
OFF: Right side of urn signal light switch off
-
Left Turn SW State (CAN)
State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF
ON: Left side of turn signal light switch on
OFF: Left side of urn signal light switch off
-
Reverse
State of the shift position R signal / OFF or ON
ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed
Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph)
Vehicle stopped: 0 km/h (0 mph)
-
Steering Angle
Steering sensor / Min.: -3072°, Max.: 3070.5°
Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage
Power supply voltage / Min.: 0 V, Max.: 50 V
11 to 14 V
-
Indicator Light Control State
Outer rear view mirror indicator dimming state / Dim OFF or Dim ON
Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV Flag
Hybrid vehicle / OFF or ON
OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag
VGRS installed / OFF or ON
OFF: VGRS not installed
ON: VGRS installed
-
Beam Axis Inspection Completeness Flag
Completion of beam axis inspection / Incompl or Compl
Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Destination Undefined Flag
Destination determination / Unfixed or Fixed
Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Angle Adjustment by Auto Alignment
Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg
Angle adjusted using auto alignment is displayed
When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Setting of Warning Indicator Current (Dim OFF)
Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA
0 to 100 mA
-
Setting of Warning Indicator Current (Dim ON)
Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA
0 to 100 mA
-
Mirror LED Duty Ratio (Blinking)
Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100%
50%
-
Buzzer Control Frequency
Frequency of the RCTA buzzer (blind spot monitor buzzer) when sounding / Min.: 1000 Hz, Max.: 2400 Hz
2400 Hz
-
Number of DTC
Number of DTC / Min.: 0, Max.: 255
When system is normal: 0
When a malfunction is detected: More than 0
-
- OFF: Any state except "ON" state