FREEZE FRAME DATA
Troubleshooting · Vehicles built from Aug 2013
| FREEZE FRAME DATA |
Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.
| CHECK FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the blind spot monitor main switch assembly (multi-function switch) on.
Turn the GTS on.
Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.
According to the display on the GTS, display the Freeze Frame Data for the selected DTC.
Blind Spot Monitor Master Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Main Switch
Blind spot monitor main switch assembly (multi-function switch) / OFF or ON
ON: Blind spot monitor main switch assembly (multi-function switch) on
OFF: Blind spot monitor main switch assembly (multi-function switch) off
-
Warning Indicator Turning on (Master)
State of the outer rear view mirror indicator LH turning on / OFF or ON
- OFF: Any state except "ON" state
- ON: Either of the following state
- During initial check
- Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated
-
Warning Indicator Flashing (Master)
State of the outer rear view mirror indicator LH flashing / OFF or ON
OFF: Any state except "ON" state
ON: Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on
-
Main Switch Indicator Status
State of the blind spot monitor indicator on the blind spot monitor main switch assembly (multi-function switch) / OFF or ON
OFF: Indicator not illuminated
ON: Indicator illuminated
-
Warning Indicator Input Circuit Voltage
The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V
Not illuminated: Below 1 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current
The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA
Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Right Turn SW State (CAN)
State of the headlight dimmer switch assembly (right turn signal light switch) / ON or OFF
ON: Right side of turn signal light switch on
OFF: Right side of turn signal light switch off
-
Left Turn SW State (CAN)
State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF
ON: Left side of turn signal light switch on
OFF: Left side of turn signal light switch off
-
Reverse
State of the shift position R signal / OFF or ON
ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed
Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph)
Vehicle stopped: 0 km/h (0 mph)
-
Steering Angle
Steering sensor / Min.: -3072°, Max.: 3070.5°
Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage
Power supply voltage / Min.: 0 V, Max.: 50 V
Always: 11 to 14 V
-
Indicator Light Control State
Outer rear view mirror indicator dimming state / Dim OFF or Dim ON
Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment
Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg
Angle adjusted using auto alignment is displayed
When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Number of DTC
Number of DTC / Min.: 0, Max.: 255
When system is normal: 0
When a malfunction is detected: More than 0
-
Blind Spot Monitor Slave Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Warning Indicator Turning on (Slave)
State of the outer rear view mirror indicator RH turning on / OFF or ON
OFF: Any state except "ON" state
ON: Either of the following state- During initial check
- Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated
-
Warning Indicator Flashing (Slave)
State of the outer rear view mirror indicator RH flashing / OFF or ON
OFF: Any state except "ON" state
ON: Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on
-
Buzzer Sound Status
State of the RCTA buzzer (blind spot monitor buzzer) / OFF or ON
OFF: Buzzer not sounding - ON: All of the following conditions are met:
- Not during initial check
- Vehicle detected in warning area of RCTA
- Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more
- Shift lever in R
- No DTC output
-
Warning Indicator Input Circuit Voltage
The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V
Not illuminated: Below 1 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current
The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA
Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Buzzer Input Circuit Voltage
RCTA buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V
Not sounding buzzer: 11 to 14 V
Sounding buzzer: Alternating between 0 to 14 V
-
Right Turn SW State (CAN)
State of the headlight dimmer switch assembly (right signal light switch) / ON or OFF
ON: Right side of turn signal light switch on
OFF: Right side of turn signal light switch off
-
Left Turn SW State (CAN)
State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF
ON: Left side of turn signal light switch on
OFF: Left side of turn signal light switch off
-
Reverse
State of the shift position R signal / OFF or ON
ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed
Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph)
Vehicle stopped: 0 km/h (0 mph)
-
Steering Angle
Steering sensor / Min.: -3072°, Max.: 3070.5°
Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage
Power supply voltage / Min.: 0 V, Max.: 50 V
Always: 11 to 14 V
-
Indicator Light Control State
Outer rear view mirror indicator dimming state / Dim OFF or Dim ON
Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment
Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg
Angle adjusted using auto alignment is displayed
When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Number of DTC
Number of DTC / Min.: 0, Max.: 255
When system is normal: 0
When a malfunction is detected: More than 0
-
- OFF: Any state except "ON" state
| CLEAR FREEZE FRAME DATA |
- NOTICE:
- Clearing the DTCs will also clear the Freeze Frame Data
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the blind spot monitor main switch assembly (multi-function switch) on.
Turn the GTS on.
Clear the DTCs and Freeze Frame Data.