2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

B15D8 Monitor Disconnected

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The parking assist ECU and radio and display receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the radio and display receiver assembly and parking assist ECU, these DTCs will be stored.
DTC Code
DTC Detection Condition
Trouble Area
B15D8
A device that is listed in the AVC-LAN connected device record of the master unit is missing.
  1. Parking assist ECU power source circuit
  2. AVC-LAN circuit
  3. Parking assist ECU
  4. Radio and display receiver assembly

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E245658E17

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)

  1. E245332E32
    Disconnect the parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I6-4 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I6-1 (+B) - I6-4 (GND1)
    Always
    11 to 14 V
    I6-8 (IG) - I6-4 (GND1)
    Ignition switch ON
    11 to 14 V
    I6-9 (ACC) - I6-4 (GND1)
    Ignition switch ACC
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Parking Assist ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

  1. E268443E03
    Remove the radio and display receiver assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (TX3+) - 8 (TX3-)
    Always
    60 to 80 Ω



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARKING ASSIST ECU)
  1. Disconnect the H50 radio and display receiver assembly connector.

  1. Disconnect the I6 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H50-7 (TX3+) - I6-11 (TX+)
    Always
    Below 1 Ω
    H50-8 (TX3-) - I6-10 (TX-)
    Always
    Below 1 Ω
    H50-7 (TX3+) - Body ground
    Always
    10 kΩ or higher
    H50-8 (TX3-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK PARKING ASSIST ECU
  1. Replace the parking assist ECU with a known good one.

    1. for LHD: Click here
    2. for RHD: Click here

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (PARKING ASSIST ECU IS DEFECTIVE)


← B15D8 Monitor Disconnected (Aug 2013 – Jul 2014)B15F5 Air Conditioner ECU Vehicle Information Reading/Writing Processor Malfunction (Aug 2013 – Jul 2014) →