Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › THROTTLE BODY
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260406 THROTTLE BODY A

2TR-FE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the throttle body with motor assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 22030 1.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the throttle body with motor assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


a.
A306999E04
1.823,0.823 2.833,0.417 2.833,0.417 2.969,0.417 false 2.063,1.646 2.615,1.833 2.615,1.833 2.75,1.833 false 3.01,0.323 3.198,0.49 0.188,0.167 10 false *a 2.771,1.75 2.958,1.917 0.188,0.167 10 false *b

Install a new gasket to the intake manifold.

Text in Illustration
*a Protrusion
*b Groove

HINT:

Align the protrusion of the gasket with the groove of the intake manifold.



b.

Install the throttle body with motor assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the water by-pass hose to the throttle body with motor assembly, and slide the clip to secure the hose.


d.

Connect the No. 2 water by-pass hose to the throttle body with motor assembly, and slide the clip to secure the hose.


e.

Connect the throttle body with motor connector.


Hide 17861 2.INSTALL INTAKE AIR CONNECTOR

a.

Install the intake air connector with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Tighten the hose clamp.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Connect the vacuum hose.


d.

Connect the No. 2 ventilation hose.


e.

Connect the vacuum hose to the air pressure sensor.


f.

Connect the air pressure sensor connector.


g.

Attach the wire harness and vacuum hose to the intake air connector.


Hide 17705 3.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

a.
A230208E03
1.316,1.943 1.581,2.101 0.265,0.158 10 45° 1.517,2.344 1.782,2.502 0.265,0.158 10 90° 0.768,1.944 0.947,2.100 0.179,0.156 10 *a 0.201,2.625 0.381,2.784 0.180,0.159 10 *b 2.907,1.992 3.095,2.153 0.188,0.161 10 *c 2.513,2.596 2.71,2.085 2.71,2.085 2.899,2.085 false 2.626,2.623 2.834,2.085 false

Install the air cleaner cap sub-assembly with air cleaner hose and align its matchmark with the matchmark of the intake air connector as shown in the illustration.

Text in Illustration
*a Upper
*b Front
*c Matchmark


b.

Tighten the hose clamp.

NOTICE:

Check that the air cleaner hose is securely installed.



c.

Attach the 4 clamps.


d.

Attach the 3 clamps and connect the intake mass air flow meter connector.


Hide 51405A 6.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 8.PERFORM INITIALIZATION

NOTICE:

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.


a.

Turn the ignition switch to ON without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above steps again.



b.

Connect the GTS to the DLC3 and clear the DTCs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).


c.

Perform "Inspection After Repairs" (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


d.

Start the engine, and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

Engine Idle Speed:
Condition Specified Condition
A/C switched off 600 to 700 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in N (neutral) or P.




e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value changes.


f.

Perform a road test and confirm that there are no abnormalities.