Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › IGNITION SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260418 IGNITION SYSTEM G

2TR-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.PERFORM SPARK TEST

a.

Check for DTCs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

NOTICE:

If any DTC is output, perform troubleshooting procedures for that DTC.



b.

Remove the 4 ignition coil assemblies and 4 spark plugs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL).


c.

Install the spark plug to the ignition coil assembly and connect the ignition coil connector.


d.

Disconnect the 4 fuel injector connectors.


e.

Ground the spark plug.


f.

Visually check that sparks occur while the engine is being cranked.

NOTICE:
·

When performing the inspection, be sure to ground the hexagonal portion or the threaded portion of the spark plug.

·

Do not crank the engine for more than 2 seconds.

·

Be sure to ground the spark plug when checking.

·

If an ignition coil assembly is struck or dropped, replace it with a new one.

·

If a spark plug is struck or dropped, replace it with a new one.




g.

If sparks do not occur normally in 1 or more cylinders, perform the "Ignition Coil and Spark Test" below.


Hide 2.INSPECT IGNITION COIL AND SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


a.

Spark test flowchart.

i.

Check that the wire harness side connector of the ignition coil assembly is securely connected.

Result:
Result Proceed to
NG Connect securely
OK Go to next step



ii.

Perform spark test on each ignition coil assembly.

1.

Replace the ignition coil assembly with a normal one.

2.

Perform spark test again.

Result:
Result Proceed to
OK Replace ignition coil assembly
NG Go to next step




iii.

Inspect the spark plug.

1.

If there is a cylinder in which ignition does not occur, interchange the spark plug of that cylinder and the spark plug of a cylinder in which ignition properly occurs.

2.

Check that sparks occur in the cylinder in which the properly functioning spark plug was installed.


Result:
Result Proceed to
OK Replace spark plug
NG Inspect ignition system (See page (Click here))



iv.

Check the camshaft position sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0340).


v.

Check the crankshaft position sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0335).



b.

Connect the 4 fuel injector connectors.


c.

Install the 4 ignition coil assemblies and 4 spark plugs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION).



Hide 19100P 3.INSPECT SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not attempt to adjust the electrode gap of a used spark plug.



HINT:

Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


a.

Check the electrode.

i.
A417417N01
0.583,2.781 0.729,2.781 0.729,2.781 1.083,2.594 false 0.417,2.688 0.729,2.885 0.313,0.198 10 false *a

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (Terminal part) - Body ground Always 10 MΩ or higher


Text in Illustration
*a Ground

HINT:

If a megohmmeter is not available, perform the following simple inspection.




b.

Alternative inspection method:

i.

Quickly accelerate the engine to 4000 rpm 5 times.


ii.

Remove the spark plug.


iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its thread and insulator.

If there is damage, replace the spark plug. If not, reinstall the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO FK20HR-A8



d.

Check the spark plug electrode gap.

Maximum electrode gap for used spark plug:

1.1 mm (0.0433 in.)


If the gap is more than the maximum, replace the spark plug.

Electrode gap for new spark plug:

0.7 to 0.8 mm (0.0276 to 0.0315 in.)


NOTICE:

When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.



e.
U110721

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Air pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Duration:

20 seconds or less


HINT:

Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.