Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a sensor plate and a pickup coil.

The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No. DTC Detection Condition Trouble Area
P0335 When either of the following conditions is met (1 trip detection logic):
·

No crankshaft position sensor signal is sent to the ECM while cranking.

·

No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or less.

·

The crankshaft position sensor signal is missing despite the camshaft position sensor signal inputs being normal after the engine is cranked.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 2 crankshaft timing sprocket (sensor plate)

·

Camshaft position sensor

·

ECM


P0339 All of the following conditions are met (1 trip detection logic):
(a) The engine speed is 1000 rpm or more.
(b) No crankshaft position sensor signal for 0.05 seconds or more.
(c) 3 seconds or more have elapsed since the starter signal switched from ON to OFF.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft

·

ECM



A254144E07
2.563,0.573 3.135,0.74 0.573,0.167 10 false 5 V/DIV. 2.969,1.635 3.323,1.802 0.354,0.167 10 false GND 1.135,2.563 2.219,2.781 1.083,0.219 10 false 20 msec./DIV. 0.146,1.615 0.458,1.813 0.313,0.198 10 false NE

Reference: Inspection using an oscilloscope.

HINT:
·

NE stands for the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.



Tester Connection Tool Setting Condition Specified Condition
C153-27 (NE+) - C153-34 (NE-) 5 V/DIV, 20 msec./DIV Idling The correct waveform is as shown


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.

If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

Crankshaft position sensor
·

Crankshaft position sensor output voltage fluctuates while crankshaft revolving

·

34 crankshaft position sensor signals per crankshaft revolution



CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0335 or P0339.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A247768E15
0.625,1.729 2.667,2.073 2.042,0.344 10 false Crankshaft Position Sensor 5.656,2.177 6.229,2.469 0.573,0.292 10 false ECM 0.625,1.573 1.01,1.781 0.385,0.208 10 false C53 1.469,0.5 1.76,0.74 0.292,0.24 10 false NE 1.448,1.083 1.875,1.323 0.427,0.24 10 false NE- 1.333,1.365 1.771,1.594 0.438,0.229 10 false GND 5.083,0.51 5.365,0.771 0.281,0.26 10 false 27 5.083,1.271 5.479,1.625 0.396,0.354 10 false 34 5.646,2.031 6.135,2.281 0.49,0.25 10 false C153 5.344,0.479 5.729,0.688 0.385,0.208 10 false NE+ 5.344,1.302 5.76,1.563 0.417,0.26 10 false NE- 1.76,0.51 1.948,0.75 0.188,0.24 10 false 1 1.76,1.292 2,1.594 0.24,0.302 10 false 3 1.76,1.052 1.969,1.292 0.208,0.24 10 false 2 3.229,1.5 3.979,1.792 0.75,0.292 10 false Shielded

CAUTION / NOTICE / HINT

HINT:

After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.

·

Installation condition of the camshaft position sensor

·

Installation condition of the camshaft

·

Connection of the camshaft position sensor connector



HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Start the engine.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as less than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.





OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.


OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C53-1 (NE) - C153-27 (NE+) Always Below 1 Ω
C53-2 (NE-) - C153-34 (NE-) Always Below 1 Ω
C53-1 (NE) or C153-27 (NE+) - Body ground Always 10 kΩ or higher
C53-2 (NE-) or C153-34 (NE-) - Body ground Always 10 kΩ or higher




OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
A208464E40
0.604,1.792 1.229,2.042 0.625,0.25 10 false OK 2.667,1.802 3.354,2.052 0.688,0.25 10 false NG 1.719,1.563 2.438,1.844 0.719,0.281 10 false Clearance

a.

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.




OK

5.INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET (TEETH OF SENSOR PLATE)

NG

5.INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate does not have any cracks or deformation.




OK

NG

REPLACE NO. 2 CRANKSHAFT TIMING SPROCKET