Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

A flat-type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.

Knock sensors are fitted onto the engine block to detect engine knocking.

Each knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327 Output voltage of the knock sensor is 0.5 V or less (1 trip detection logic).
·

Short in knock sensor circuit


·

Knock sensor


·

ECM


P0328 Output voltage of the knock sensor is 4.5 V or higher (1 trip detection logic).
·

Open in knock sensor circuit


·

Knock sensor


·

ECM



HINT:

When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A150243E01
0.336,0.512 1.924,0.727 1.588,0.215 10 KNK1 Signal Waveform 2.632,1.857 2.985,2.060 0.353,0.203 10 GND 2.503,1.065 3.067,1.268 0.564,0.203 10 1 V/DIV. 0.915,2.821 1.757,3.024 0.842,0.203 10 1 msec./DIV.

Tester Connection Tool Setting Condition Specified Condition
C154-20 (KNK1) - C154-28 (EKNK) 1 V/DIV.
1 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown

MONITOR DESCRIPTION

The ECM also senses background engine noise with the knock sensor and uses this noise to check for faults in the sensor. If the knock sensor output voltage is outside the normal range, the ECM interprets this as a fault in the knock sensor and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0327 or P0328.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A247767E11
0.896,1.99 1,2.146 0.104,0.156 10 false 1 0.906,0.948 1.01,1.104 0.104,0.156 10 false 2 0.302,2.063 0.51,2.208 0.208,0.146 10 false h3 0.302,2.198 1.229,2.385 0.927,0.188 10 false Knock Sensor 5.688,0.771 5.865,0.927 0.177,0.156 10 false 20 5.938,0.781 6.323,0.938 0.385,0.156 10 false KNK1 5.688,1.958 5.875,2.115 0.188,0.156 10 false 28 5.938,1.979 6.375,2.135 0.438,0.156 10 false EKNK 6.198,3.333 6.531,3.49 0.333,0.156 10 false ECM 4.625,2.292 4.698,2.427 0.073,0.135 10 false * 0.448,3.292 1.177,3.49 0.729,0.198 10 false *: Shielded 3.25,0.875 3.573,1.031 0.323,0.156 10 false Ch3 3.25,2.063 3.573,2.219 0.323,0.156 10 false Ch3 6.198,3.177 6.594,3.385 0.396,0.208 10 false C154 3.354,0.688 3.469,0.844 0.115,0.156 10 false 2 3.354,1.875 3.469,2.031 0.115,0.156 10 false 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING KNOCK SENSOR (KNOCK FEEDBACK VALUE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Knock Feedback Value.


f.

Read the value while driving the vehicle.

OK:

The value changes.


HINT:
Malfunction does not occur Knock Feedback Value changes
Malfunctions occur Knock Feedback Value does not change

The Knock Feedback Value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.




OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
U147510E03
0.292,0.083 0.688,0.302 0.396,0.219 10 false *a 0.333,1.042 0.656,1.333 0.323,0.292 10 false h3

a.

Disconnect the knock control sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
h3-2 - h3-1 Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Knock Control Sensor)



OK

3.INSPECT KNOCK CONTROL SENSOR

NG

4.CHECK HARNESS AND CONNECTOR
3.INSPECT KNOCK CONTROL SENSOR
a.

HINT:

Perform "Inspection After Repair" after replacing the knock control sensor (See pageEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).



OK

NG

4.CHECK HARNESS AND CONNECTOR
a.

Disconnect the knock control sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h3-2 - C154-20 (KNK1) Always Below 1 Ω
h3-1 - C154-28 (EKNK) Always Below 1 Ω
h3-2 or C154-20 (KNK1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR