Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned to on (IG), battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the No. 1 integration relay (EFI) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

for Automatic Transmission

A358809E02
5.448,1.885 5.729,2.031 0.281,0.146 10 false G55 5.458,2.646 5.75,2.792 0.292,0.146 10 false G55 5.458,2.99 5.75,3.135 0.292,0.146 10 false G55 5.469,3.25 5.76,3.396 0.292,0.146 10 false G56 5.469,3.75 5.76,3.896 0.292,0.146 10 false C36 5.25,1.74 5.438,1.896 0.188,0.156 10 false 21 5.25,2.521 5.438,2.677 0.188,0.156 10 false 22 5.25,2.865 5.438,3.021 0.188,0.156 10 false 23 5.25,3.135 5.438,3.292 0.188,0.156 10 false 36 5.229,3.615 5.417,3.771 0.188,0.156 10 false 12 5.833,1.729 6.271,1.875 0.438,0.146 10 false IGSW 5.823,2.646 6.115,2.813 0.292,0.167 10 false +B2 5.823,2.969 6.115,3.135 0.292,0.167 10 false +B 5.823,3.229 6.26,3.375 0.438,0.146 10 false MREL 5.823,3.729 6.115,3.896 0.292,0.167 10 false E1 3.448,0.458 3.74,0.604 0.292,0.146 10 false G50 2.135,0.302 2.427,0.448 0.292,0.146 10 false G51 2.135,0.646 2.427,0.792 0.292,0.146 10 false G51 3.531,0.26 3.635,0.427 0.104,0.167 10 false 8 2.219,0.094 2.323,0.26 0.104,0.167 10 false 2 2.229,0.833 2.333,1 0.104,0.167 10 false 1 3.573,2.438 3.844,2.604 0.271,0.167 10 false IG2 2.813,1.74 3.083,1.906 0.271,0.167 10 false IG2 3.552,2.656 3.823,2.823 0.271,0.167 10 false EFI 2.813,2.844 3.104,3.01 0.292,0.167 10 false EFI 2.167,2.135 2.396,2.302 0.229,0.167 10 false 1A 4.208,1.885 4.438,2.052 0.229,0.167 10 false 1A 4.208,2.135 4.438,2.302 0.229,0.167 10 false 1A 4.208,2.99 4.438,3.156 0.229,0.167 10 false 1B 4.198,3.25 4.427,3.417 0.229,0.167 10 false 1B 2.177,2.99 2.406,3.156 0.229,0.167 10 false 1C 2.177,3.25 2.406,3.417 0.229,0.167 10 false 1B 2.229,2.792 2.333,2.958 0.104,0.167 10 false 1 4.281,2.323 4.385,2.49 0.104,0.167 10 false 1 4.26,3.417 4.365,3.583 0.104,0.167 10 false 2 2.24,1.938 2.344,2.104 0.104,0.167 10 false 3 2.219,3.417 2.323,3.583 0.104,0.167 10 false 3 4.26,2.781 4.365,2.948 0.104,0.167 10 false 4 4.271,1.677 4.375,1.844 0.104,0.167 10 false 5 1.031,2.438 1.375,2.604 0.344,0.167 10 false P/I-B 0.854,0.167 1.167,0.313 0.313,0.146 10 false AM2 2.667,3.729 4.156,3.896 1.49,0.167 10 false No. 1 Integration Relay 2.021,0.979 4.25,1.125 2.229,0.146 10 false Power Management Control ECU 0.771,4 1.25,4.188 0.479,0.188 10 false Battery 6.104,4.208 6.458,4.438 0.354,0.229 10 false ECM 2.49,0.635 2.885,0.781 0.396,0.146 10 false AM22 2.479,0.292 2.875,0.438 0.396,0.146 10 false AM21 3.021,0.448 3.396,0.594 0.375,0.146 10 false IG2D 4.938,2.042 5.25,2.188 0.313,0.146 10 false IGN

for Manual Transmission

A358809E01
5.448,1.885 5.729,2.031 0.281,0.146 10 false G56 5.458,2.656 5.75,2.802 0.292,0.146 10 false G55 5.458,2.99 5.75,3.135 0.292,0.146 10 false G55 5.458,3.26 5.75,3.406 0.292,0.146 10 false G55 5.469,3.75 5.76,3.896 0.292,0.146 10 false C36 5.25,1.708 5.438,1.865 0.188,0.156 10 false 21 5.25,2.479 5.438,2.635 0.188,0.156 10 false 23 5.25,2.833 5.438,2.99 0.188,0.156 10 false 22 5.229,3.594 5.417,3.75 0.188,0.156 10 false 12 5.271,3.135 5.406,3.292 0.135,0.156 10 false 9 5.833,1.729 6.271,1.875 0.438,0.146 10 false IGSW 5.823,2.635 6.115,2.802 0.292,0.167 10 false +B2 5.823,2.969 6.115,3.135 0.292,0.167 10 false +B 5.823,3.229 6.26,3.375 0.438,0.146 10 false MREL 5.823,3.729 6.115,3.896 0.292,0.167 10 false E1 3.438,0.458 3.729,0.604 0.292,0.146 10 false G50 2.135,0.302 2.427,0.448 0.292,0.146 10 false G51 2.135,0.646 2.427,0.792 0.292,0.146 10 false G51 3.521,0.26 3.625,0.427 0.104,0.167 10 false 8 2.219,0.094 2.323,0.26 0.104,0.167 10 false 2 2.229,0.823 2.333,0.99 0.104,0.167 10 false 1 3.573,2.438 3.844,2.604 0.271,0.167 10 false IG2 2.813,1.719 3.083,1.885 0.271,0.167 10 false IG2 3.552,2.656 3.823,2.823 0.271,0.167 10 false EFI 2.813,2.833 3.104,3 0.292,0.167 10 false EFI 2.167,2.135 2.396,2.302 0.229,0.167 10 false 1A 4.208,1.885 4.438,2.052 0.229,0.167 10 false 1A 4.208,2.135 4.438,2.302 0.229,0.167 10 false 1A 4.208,3 4.438,3.167 0.229,0.167 10 false 1B 4.198,3.25 4.427,3.417 0.229,0.167 10 false 1B 2.177,2.99 2.406,3.156 0.229,0.167 10 false 1C 2.177,3.25 2.406,3.417 0.229,0.167 10 false 1B 2.229,2.781 2.333,2.948 0.104,0.167 10 false 1 4.271,2.313 4.375,2.479 0.104,0.167 10 false 1 4.26,3.438 4.365,3.604 0.104,0.167 10 false 2 2.24,1.938 2.344,2.104 0.104,0.167 10 false 3 2.219,3.448 2.323,3.615 0.104,0.167 10 false 3 4.26,2.792 4.365,2.958 0.104,0.167 10 false 4 4.271,1.688 4.375,1.854 0.104,0.167 10 false 5 1.031,2.448 1.375,2.615 0.344,0.167 10 false P/I-B 0.854,0.156 1.167,0.302 0.313,0.146 10 false AM2 2.667,3.719 4.156,3.885 1.49,0.167 10 false No. 1 Integration Relay 2.021,1.01 4.25,1.156 2.229,0.146 10 false Power Management Control ECU 0.771,4.01 1.25,4.198 0.479,0.188 10 false Battery 6.115,4.208 6.469,4.438 0.354,0.229 10 false ECM 2.479,0.625 2.875,0.771 0.396,0.146 10 false AM22 2.479,0.292 2.875,0.438 0.396,0.146 10 false AM21 3.021,0.448 3.396,0.594 0.375,0.146 10 false IG2D 4.938,2.042 5.25,2.188 0.313,0.146 10 false IGN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)
U147598E01
0.48,1.007 0.678,1.170 0.198,0.163 10 1C 0.085,0.079 0.275,0.255 0.191,0.177 10 *a 0.093,3.912 0.277,4.067 0.184,0.156 10 *1 0.93,1.901 1.039,2.056 0.110,0.156 10 1 0.597,1.551 0.921,1.932 false

a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*a Front view of wire harness connector
(to No. 1 Integration Relay)


c.

Reinstall the No. 1 integration relay.



OK

2.INSPECT NO. 1 INTEGRATION RELAY (EFI AND IG2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 1 INTEGRATION RELAY (EFI AND IG2)

OK

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)

NG

REPLACE NO. 1 INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
a.

Check the harness and connectors between the No. 1 integration relay and ECM.

i.

Remove the No. 1 integration relay from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
G56-36 (MREL) - 1B-2 Always Below 1 Ω
G55-23 (+B) - 1B-4 Always Below 1 Ω
G55-22 (+B2) - 1B-4 Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
G55-9 (MREL) - 1B-2 Always Below 1 Ω
G55-22 (+B) - 1B-4 Always Below 1 Ω
G55-23 (+B2) - 1B-4 Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
G56-36 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
G55-23 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
G55-22 (+B2) or 1B-4 - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
G55-9 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
G55-22 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
G55-23 (+B2) or 1B-4 - Body ground Always 10 kΩ or higher



iv.

Reinstall the No. 1 integration relay.


v.

Reconnect the ECM connector.



b.

Check the harness and connectors between the No. 1 integration relay and body ground.

i.

Remove the No. 1 integration relay from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1B-3 - Body ground Always Below 1 Ω



iii.

Reinstall the No. 1 integration relay.




OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C36-12 (E1) - Body ground Always Below 1 Ω



c.

Reconnect the ECM connector.



OK

5.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW VOLTAGE)
U169407E01
2.375,1.75 2.698,2.74 false 0.802,1.927 0.448,2.76 false 1.094,1.833 1.25,2.406 false 0.521,1.167 0.823,1.333 0.302,0.167 10 false G55 0.979,1.156 1.281,1.323 0.302,0.167 10 false G56 2.104,1.167 2.406,1.333 0.302,0.167 10 false C36 0.073,0.01 0.292,0.219 0.219,0.208 10 false *a 0.344,2.802 1.219,2.979 0.875,0.177 10 false 21 (IGSW)*A 1.188,2.427 2.063,2.604 0.875,0.177 10 false 21 (IGSW)*B 2.635,2.76 3.135,2.938 0.5,0.177 10 false 12 (E1)

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Automatic Transmission
Tester Connection Switch Condition Specified Condition
G55-21 (IGSW) - C36-12 (E1) Engine switch on (IG) 11 to 14 V

for Manual Transmission
Tester Connection Switch Condition Specified Condition
G56-21 (IGSW) - C36-12 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*A for Automatic Transmission
*B for Manual Transmission
*a Component with harness connected
(ECM)



OK

NG

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, NO. 1 INTEGRATION RELAY - BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
1A-5 - G55-21 (IGSW) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
1A-5 - G56-21 (IGSW) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
1A-5 or G55-21 (IGSW) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
1A-5 or G56-21 (IGSW) - Body ground Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the ECM connector.



OK

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G50-8 (IG2D) - 1A-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G50-8 (IG2D) or 1A-1 - Body ground Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the power management control ECU connector.



OK

8.CHECK ENTRY AND START SYSTEM (POWER SOURCE MODE DOES NOT CHANGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR