Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

When the engine switch is pushed with the key in the cabin, the power management control ECU receives signals to switch the power source mode.

WIRING DIAGRAM

C217209E11
2.656,5.594 3.938,5.917 1.281,0.323 10 false Power Management Control ECU 2.635,4.469 2.74,4.625 0.104,0.156 10 false 6 2.635,4.875 2.76,5.052 0.125,0.177 10 false 5 2.542,5.063 2.854,5.229 0.313,0.167 10 false G51 2.542,4.667 2.833,4.813 0.292,0.146 10 false G51 2.594,3.385 2.771,3.552 0.177,0.167 10 false 18 2.177,3.469 2.313,3.646 0.135,0.177 10 false 7 2.177,3.865 2.271,4.031 0.094,0.167 10 false 2 0.865,3.885 0.99,4.052 0.125,0.167 10 false 5 2.594,3.792 2.771,3.938 0.177,0.146 10 false 17 2.542,3.969 2.896,4.146 0.354,0.177 10 false G51 2.531,3.583 2.958,3.729 0.427,0.146 10 false G51 2.906,3.99 3.354,4.167 0.448,0.177 10 false SSW2 2.896,3.594 3.354,3.771 0.458,0.177 10 false SSW1 1.802,3.99 2.104,4.177 0.302,0.188 10 false SS2 1.083,3.979 1.406,4.146 0.323,0.167 10 false GND 1,4.333 1.354,4.49 0.354,0.156 10 false G36 1,4.5 2.021,4.677 1.021,0.177 10 false Engine Switch 1.813,3.594 2.073,3.75 0.26,0.156 10 false SS1 2.635,1.656 2.729,1.802 0.094,0.146 10 false 8 2.552,1.844 2.833,2.021 0.281,0.177 10 false G50 3.844,2.052 4.021,2.208 0.177,0.156 10 false 20 3.792,2.26 4.135,2.427 0.344,0.167 10 false G51 4.51,2.052 4.688,2.229 0.177,0.177 10 false 52 4.51,2.271 4.729,2.438 0.219,0.167 10 false 2A 0.469,1.76 0.573,1.906 0.104,0.146 10 false 3 0.583,2.521 1.573,2.708 0.99,0.188 10 false 1A*1, 1J*2 4.521,4.208 4.698,4.365 0.177,0.156 10 false 48 4.521,4.417 4.729,4.594 0.208,0.177 10 false 2A 6.542,4.219 6.646,4.375 0.104,0.156 10 false 4 6.448,4.417 6.698,4.573 0.25,0.156 10 false 2D 5.292,1.604 6.01,1.823 0.719,0.219 10 false IG1 No. 1 5.302,2.542 6.104,2.719 0.802,0.177 10 false IG1 No. 2 5.281,3.521 6.104,3.729 0.823,0.208 10 false IG1 No. 3 5.427,4.688 5.854,4.833 0.427,0.146 10 false ACC 4.417,5.479 6.76,5.719 2.344,0.24 10 false Driver Side Junction Block Assembly 2.917,1.844 3.281,2.021 0.365,0.177 10 false IG2D 3.365,2.271 3.708,2.448 0.344,0.177 10 false IG1D 2.635,0.854 2.802,1.073 0.167,0.219 10 false 1 2.542,1.052 2.844,1.219 0.302,0.167 10 false G51 2.917,1.042 3.313,1.229 0.396,0.188 10 false AM22 2.646,0.448 2.76,0.594 0.115,0.146 10 false 2 2.542,0.656 2.969,0.813 0.427,0.156 10 false G51 1.531,0.802 1.875,0.99 0.344,0.188 10 false AM2 1.26,2.125 1.51,2.292 0.25,0.167 10 false IG2 0.25,0.646 1.115,0.969 0.865,0.323 10 false from Battery 0.583,2.677 2.198,3.042 1.615,0.365 10 false Engine Room Relay Block (NO. 1 Integration Relay) 2.917,0.656 3.302,0.823 0.385,0.167 10 false AM21 3.802,4.417 4.094,4.563 0.292,0.146 10 false G51 3.865,4.208 4.042,4.365 0.177,0.156 10 false 19 2.896,5.063 3.313,5.208 0.417,0.146 10 false GND2 2.896,4.667 3.229,4.813 0.333,0.146 10 false GND 3.302,4.427 3.729,4.625 0.427,0.198 10 false ACCD 2.208,1.604 2.667,1.802 0.458,0.198 10 false 1*1 2.219,1.75 2.677,1.948 0.458,0.198 10 false 6*2 4.438,5.906 7.156,6.208 2.719,0.302 10 false *1: except 1GD-FTV (w/ Urea SCR System) 4.438,6.25 7.156,6.552 2.719,0.302 10 false *2: for 1GD-FTV (w/ Urea SCR System)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

OK

3.READ VALUE USING INTELLIGENT TESTER (KEY CERTIFI WAIT T-OUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.READ VALUE USING INTELLIGENT TESTER (KEY CERTIFI WAIT T-OUT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the intelligent tester on.

HINT:

When using the intelligent tester with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.



c.

Enter the following menus: Body / Power Source Control / Data List.


d.

Read the Data List and check that "No" is displayed 1 second after turning the engine switch from off to on (IG).

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Certifi Wait T-Out Key certification waiting timed out / Yes or No Yes: Key certification waiting timed out
No: Key certification completed within specified time
-

OK:

"No" is displayed 1 second after turning the engine switch from off to on (IG).




OK

4.READ VALUE USING INTELLIGENT TESTER (START SWITCH 1, 2)

NG

9.CHECK FOR DTC
4.READ VALUE USING INTELLIGENT TESTER (START SWITCH 1, 2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Start Switch1 Start Switch 1 / ON or OFF ON: Engine switch pushed
OFF: Engine switch not pushed
-
Start Switch2 Start Switch 2 / ON or OFF ON: Engine switch pushed
OFF: Engine switch not pushed
-

OK:

The display changes in response to the operation of the engine switch.




OK

5.CHECK POWER MANAGEMENT CONTROL ECU

NG

7.INSPECT ENGINE SWITCH
5.CHECK POWER MANAGEMENT CONTROL ECU
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

Read the Data List and check that the display changes according to the changes in the power source mode when the engine switch is pushed.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition Power Supply Condition / IG2 ON, ST ON, All OFF, IG1 ON or ACC ON IG2 ON: IG2 relay on
ST ON: ST request signal on
All OFF: All relays off
IG1 ON: IG1 relay on
ACC ON: ACC relay on
-

OK:

Display changes according to the changes in the power source mode when the engine switch is pushed.



f.

Measure the voltage according to the value(s) in the table below.

U169910E01
0.135,0.091 0.337,0.251 0.202,0.160 10 *a 3.475,0.566 3.816,0.737 0.341,0.172 10 IG2D 5.707,0.615 6.144,0.787 0.437,0.172 10 IG1D 3.438,0.647 3.363,0.647 3.363,0.647 3.233,1.451 false 5.305,1.637 5.564,0.677 5.564,0.677 5.676,0.677 false 6.117,1.055 6.555,1.227 0.437,0.172 10 ACCD 5.409,1.648 5.883,1.117 5.883,1.117 6.086,1.117 false 2.433,0.772 2.757,0.953 0.324,0.181 10 G50 4.514,0.772 4.839,0.953 0.324,0.181 10 G51

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)
- -

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G51-20 (IG1D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC)
Engine switch on (IG) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
G50-8 (IG2D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC)
Engine switch on (IG) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
G51-19 (ACCD) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
Engine switch on (IG) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher




OK

6.CONFIRMATION TEST

NG

6.CONFIRMATION TEST
a.

Check that the power source mode changes to on (ACC) and on (IG) when operating the engine switch.

OK:

The power source mode changes to on (ACC) and on (IG) in response to the operation of the engine switch.




OK

NG

CHECK RELAY CONTACT SIDE CIRCUIT

7.INSPECT ENGINE SWITCH
a.
A207999E07
0.823,1.938 0.927,1.938 0.927,1.938 1.552,0.958 false 0.604,1.615 0.708,1.615 0.708,1.615 1.219,0.958 false 2.76,1.365 2.656,1.365 2.656,1.365 2.052,0.958 false 0.135,0.031 0.344,0.198 0.208,0.167 10 false *a 0.5,1.854 0.875,2.052 0.375,0.198 10 false GND 0.292,1.531 0.635,1.729 0.344,0.198 10 false SS1 2.813,1.281 3.156,1.479 0.344,0.198 10 false SS2

Remove the engine switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (SS1) - 5 (GND) Engine switch not pushed 10 kΩ or higher
Engine switch pushed Below 1 Ω
2 (SS2) - 5 (GND) Engine switch not pushed 10 kΩ or higher
Engine switch pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(Engine Switch)

HINT:




OK

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE SWITCH)

NG

REPLACE ENGINE SWITCH

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE SWITCH)
a.

Disconnect the G51 power management control ECU connector.


b.

Disconnect the G36 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-17 (SSW2) - G36-2 (SS2) Always Below 1 Ω
G51-18 (SSW1) - G36-7 (SS1)
G51-17 (SSW2) - Body ground Always 10 kΩ or higher
G51-18 (SSW1) - Body ground
G36-5 (GND) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source / DTC.


e.

Read the DTCs.


f.

Enter the following menus: Body / Entry&Start / DTC.


g.

Read the DTCs.

Result
Result Proceed to
None of the following DTCs are output:
B2785 Communication Malfunction between ECUs Connected by LIN
B2287 LIN Communication Master Malfunction
B2784 Antenna Coil Open/Short
A
DTC B2287 is output but B2785 is not B
A DTC other than B2287 is output. C



A

GO TO ENTRY AND START SYSTEM (FOR ENTRY FUNCTION) (Room Oscillator does not Recognize Key)

B

C