Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  P0332  Knock Sensor 2 Circuit Low Input (Bank 2)  P0333  Knock Sensor 2 Circuit High Input (Bank 2)  


DESCRIPTION

Flat-type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 5 kHz and 15 kHz.

A knock sensor is fitted onto the engine block to detect engine knocking.

The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327
P0332
The output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
·

Short in knock sensor circuit

·

Knock sensor

·

ECM


P0328
P0333
The output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
·

Open in knock sensor circuit

·

Knock sensor

·

ECM



HINT:

When DTC P0327, P0328, P0332 or P0333 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues fail-safe mode until the engine switch is turned off.


Reference: Inspection using an oscilloscope

A185975E01
0.34,0.322 1.857,0.505 1.517,0.184 10 KNK1 Signal Waveform 2.551,0.78 3.114,0.964 0.563,0.184 10 1 V/DIV. 2.654,1.616 3.014,1.791 0.360,0.174 10 GND 0.408,2.533 1.231,2.716 0.823,0.183 10 1 msec./DIV.

The correct waveform is as shown.

Item Content
Terminal KNK1 - EKNK
KNK2 - EKN2
Equipment Setting 1 V/DIV.
1 msec./DIV.
Condition Engine speed maintained at 4000 rpm with warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run when 5 seconds have elapsed since the engine was started.

If the malfunction is not repaired successfully, DTC P0327, P0328, P0332 or P0333 is stored 5 seconds after the engine is next started.

WIRING DIAGRAM

A358815E01
0.444,1.289 0.675,1.483 0.231,0.194 10 h2 0.444,1.475 2.219,1.669 1.776,0.194 10 Knock Sensor 1 (for Bank 1) 0.688,1.012 0.872,1.242 0.185,0.230 10 1 1.83,1.012 2.015,1.242 0.185,0.230 10 2 0.444,3.673 0.675,3.867 0.231,0.194 10 h1 0.444,3.858 2.240,4.052 1.796,0.194 10 Knock Sensor 2 (for Bank 2) 0.688,3.396 0.872,3.626 0.185,0.230 10 1 1.83,3.396 2.015,3.626 0.185,0.230 10 2 2.224,2.168 2.815,2.370 0.591,0.202 10 Shielded 2.224,4.553 2.815,4.755 0.591,0.202 10 Shielded 3.38,0.729 3.554,0.903 0.174,0.174 10 2 3.284,0.903 3.612,1.068 0.328,0.165 10 Ch1 3.38,1.528 3.554,1.702 0.174,0.174 10 5 3.284,1.702 3.612,1.867 0.328,0.165 10 Ch1 3.38,2.327 3.554,2.500 0.174,0.174 10 1 3.284,2.501 3.612,2.665 0.328,0.165 10 Ch1 3.38,3.108 3.554,3.281 0.174,0.174 10 4 3.284,3.282 3.612,3.446 0.328,0.165 10 Ch1 3.38,3.903 3.554,4.077 0.174,0.174 10 6 3.284,4.077 3.612,4.242 0.328,0.165 10 Ch1 4.571,2.168 5.172,2.334 0.600,0.166 10 Shielded 4.571,4.553 5.172,4.719 0.600,0.166 10 Shielded 5.822,0.817 6.223,0.987 0.401,0.170 10 KNK1 5.558,0.817 5.767,0.987 0.209,0.170 10 11 5.822,1.614 6.223,1.784 0.401,0.170 10 EKNK 5.548,1.614 5.734,1.784 0.186,0.170 10 12 5.822,3.212 6.223,3.382 0.401,0.170 10 KNK2 5.581,3.212 5.706,3.382 0.126,0.170 10 5 5.822,4.011 6.223,4.181 0.401,0.170 10 EKN2 5.581,4.011 5.720,4.181 0.140,0.170 10 6 5.853,5 6.167,5.142 0.315,0.142 10 C35 5.853,5.14 6.245,5.309 0.392,0.170 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.

·

DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (CHECK KNOCK SENSOR CIRCUIT)
A378885E01
1.427,0.26 1.885,0.458 0.458,0.198 10 false Ch1 1.49,2.792 1.948,2.99 0.458,0.198 10 false Ch1 0.177,0.625 0.385,0.813 0.208,0.188 10 false *1 0.219,1.104 0.427,1.292 0.208,0.188 10 false 1 0.604,1.104 0.813,1.292 0.208,0.188 10 false 2 0.26,1.969 0.469,2.156 0.208,0.188 10 false 1 0.635,1.969 0.844,2.156 0.208,0.188 10 false 2 1.167,0.927 1.313,1.115 0.146,0.188 10 false 2 1.167,1.313 1.313,1.5 0.146,0.188 10 false 5 1.167,1.719 1.313,1.906 0.146,0.188 10 false 4 1.167,2.094 1.313,2.281 0.146,0.188 10 false 6 1.813,2.104 1.958,2.292 0.146,0.188 10 false 6 1.823,1.698 1.969,1.885 0.146,0.188 10 false 4 1.833,1.313 1.979,1.5 0.146,0.188 10 false 5 1.823,0.927 1.969,1.115 0.146,0.188 10 false 2 2.458,2.177 2.604,2.365 0.146,0.188 10 false 6 2.458,1.802 2.604,1.99 0.146,0.188 10 false 5 2.406,1.438 2.615,1.635 0.208,0.198 10 false 12 2.396,1.031 2.604,1.229 0.208,0.198 10 false 11 2.833,0.344 3.042,0.531 0.208,0.188 10 false *2 0.313,3.24 0.521,3.427 0.208,0.188 10 false *a 2.729,3.167 2.938,3.354 0.208,0.188 10 false *b

a.

Disconnect the Ch1 connector.


b.

Using lead wires, connect the connectors as follows:


Male Connector - Female Connector
Terminal 2 - Terminal 4
Terminal 5 - Terminal 6
Terminal 4 - Terminal 2
Terminal 6 - Terminal 5

c.

Warm up the engine.


d.

Run the engine at 3000 rpm for 10 seconds or more.


e.

Connect the GTS to the DLC3.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
DTC is same as when vehicle was brought in
(for example, P0327 and P0328 are output again, or P0332 and P0333 are output again)
A
DTC is different from when vehicle was brought in
(for example, P0327 and P0328 are output at first, but then P0332 and P0333 are output, or vice versa)
B

Text in Illustration
*1 Knock Sensor
*2 ECM
*a Front view of wire harness connector
(to Knock Sensor Wire)
*b Front view of wire harness connector
(to ECM Wire)


i.

Reconnect the Ch1 connector.



A

2.CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)

B

4.INSPECT KNOCK SENSOR
2.CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)
a.

Disconnect the Ch1 connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Ch1 female connector 2 - C35-11 (KNK1) Always Below 1 Ω
Ch1 female connector 5 - C35-12 (EKNK) Always Below 1 Ω
Ch1 female connector 4 - C35-5 (KNK2) Always Below 1 Ω
Ch1 female connector 6 - C35-6 (EKN2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Ch1 female connector 2 or C35-11 (KNK1) - Body ground Always 10 kΩ or higher
Ch1 female connector 5 or C35-12 (EKNK) - Body ground Always 10 kΩ or higher
Ch1 female connector 4 or C35-5 (KNK2) - Body ground Always 10 kΩ or higher
Ch1 female connector 6 or C35-6 (EKN2) - Body ground Always 10 kΩ or higher



d.

Reconnect the Ch1 connector.


e.

Reconnect the ECM connector.



OK

3.INSPECT ECM (VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VOLTAGE)
U147473E03
0.479,1.021 0.792,1.198 0.313,0.177 10 false Ch1 0.177,0.031 0.365,0.25 0.188,0.219 10 false *a

a.

Disconnect the Ch1 connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Ch1 female connector 2 - 5 Engine switch on (IG) 4.5 to 5.5 V
Ch1 female connector 4 - 6 Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to ECM Wire)


c.

Reconnect the Ch1 connector.



OK

NG

4.INSPECT KNOCK SENSOR
U147415E02
0.698,0.906 1.01,1.094 0.313,0.188 10 false Ch1 0.188,0.115 0.406,0.323 0.219,0.208 10 false *a

a.

Disconnect the Ch1 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ch1 male connector 2 - 5 20°C (68°F) 120 to 280 kΩ
Ch1 male connector 4 - 6 20°C (68°F) 120 to 280 kΩ


Text in Illustration
*a Front view of wire harness connector
(to Knock Sensor Wire)


c.

Reconnect the Ch1 connector.



OK

NG

5.CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)
5.CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)
HINT:
·

If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit of the right bank.

·

If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit of the left bank.



a.

Disconnect the Ch1 connector.


b.

Disconnect the knock sensor connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Ch1 male connector 2 - h2-2 Always Below 1 Ω
Ch1 male connector 5 - h2-1 Always Below 1 Ω
Ch1 male connector 4 - h1-2 Always Below 1 Ω
Ch1 male connector 6 - h1-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Ch1 male connector 2 or h2-2 - Body ground Always 10 kΩ or higher
Ch1 male connector 5 or h2-1 - Body ground Always 10 kΩ or higher
Ch1 male connector 4 or h1-2 - Body ground Always 10 kΩ or higher
Ch1 male connector 6 or h1-1 - Body ground Always 10 kΩ or higher



d.

Reconnect the Ch1 connector.

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the knock control sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR