Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce HC emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signal sent to the purge VSV so that the intake amount of HC emissions is appropriate for driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443 The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



WIRING DIAGRAM

for Automatic Transmission

A227122E09
1.198,0.563 1.833,0.729 0.635,0.167 10 false EFI NO. 2 2.646,0.719 3.073,0.885 0.427,0.167 10 false C138 2.646,0.865 3.385,1.042 0.74,0.177 10 false Purge VSV 2.573,0.271 2.688,0.438 0.115,0.167 10 false 1 3.354,0.271 3.469,0.438 0.115,0.167 10 false 2 5.198,0.417 5.5,0.573 0.302,0.156 10 false C37 5.229,0.229 5.427,0.396 0.198,0.167 10 false 10 5.531,0.406 5.875,0.573 0.344,0.167 10 false PRG 5.188,2.042 5.49,2.198 0.302,0.156 10 false G56 5.24,1.823 5.458,1.99 0.219,0.167 10 false 36 5.531,2.146 5.979,2.313 0.448,0.167 10 false MREL 4.469,1.49 4.583,1.656 0.115,0.167 10 false 4 4.427,1.677 4.656,1.844 0.229,0.167 10 false 1B 4.469,1.854 4.583,2.021 0.115,0.167 10 false 2 4.427,2.031 4.656,2.198 0.229,0.167 10 false 1B 2.688,1.458 2.802,1.625 0.115,0.167 10 false 1 2.646,1.667 2.875,1.833 0.229,0.167 10 false 1C 2.688,1.854 2.802,2.021 0.115,0.167 10 false 3 2.646,2.031 2.875,2.198 0.229,0.167 10 false 1B 3.083,1.781 3.354,1.948 0.271,0.167 10 false EFI 3.813,2.375 4.458,2.542 0.646,0.167 10 false EFI 3.104,2.771 4.677,2.958 1.573,0.188 10 false No. 1 Integration Relay 1.333,1.854 1.688,2.021 0.354,0.167 10 false P/I-B 0.823,2.5 1.313,2.698 0.49,0.198 10 false Battery

for Manual Transmission

A227122E10
1.198,0.552 1.833,0.719 0.635,0.167 10 false EFI No. 2 2.646,0.729 3.073,0.896 0.427,0.167 10 false C138 2.646,0.875 3.385,1.052 0.74,0.177 10 false Purge VSV 2.573,0.271 2.688,0.438 0.115,0.167 10 false 1 3.354,0.271 3.469,0.438 0.115,0.167 10 false 2 5.188,0.427 5.49,0.583 0.302,0.156 10 false C36 5.229,0.229 5.427,0.396 0.198,0.167 10 false 18 5.531,0.417 5.875,0.583 0.344,0.167 10 false PRG 5.188,2.042 5.521,2.208 0.333,0.167 10 false G55 5.281,1.823 5.427,1.99 0.146,0.167 10 false 9 5.531,2.156 5.979,2.323 0.448,0.167 10 false MREL 4.469,1.458 4.583,1.625 0.115,0.167 10 false 4 4.427,1.688 4.656,1.854 0.229,0.167 10 false 1B 4.469,1.865 4.583,2.031 0.115,0.167 10 false 2 4.427,2.031 4.656,2.198 0.229,0.167 10 false 1B 2.688,1.458 2.802,1.625 0.115,0.167 10 false 1 2.646,1.667 2.875,1.833 0.229,0.167 10 false 1C 2.688,1.844 2.802,2.01 0.115,0.167 10 false 3 2.646,2.021 2.875,2.188 0.229,0.167 10 false 1B 3.094,1.802 3.365,1.969 0.271,0.167 10 false EFI 3.813,2.344 4.083,2.51 0.271,0.167 10 false EFI 3.104,2.771 4.677,2.958 1.573,0.188 10 false No. 1 Integration Relay 1.333,1.844 1.688,2.01 0.354,0.167 10 false P/I-B 0.823,2.5 1.313,2.698 0.49,0.198 10 false Battery

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A225197E07
2.552,1.76 0.385,0.615 true 1.625,0.708 1,0.26 true 0.823,0.135 1,0.302 0.177,0.167 10 false *1 0.188,0.51 0.365,0.677 0.177,0.167 10 false *2

Connect the GTS to the DLC3.


b.

Remove the vacuum hose of the purge VSV from the charcoal canister.


c.

Start the engine and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


e.

When the purge VSV is operated using the GTS, check whether the disconnected hose applies suction to your finger.

OK:
GTS Operation Specified Condition
VSV is ON Disconnected hose applies suction to finger
VSV is OFF Disconnected hose applies no suction to finger


Text in Illustration
*1 Purge VSV
*2 Hose (to Canister)



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

OK

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

NG

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
U169101E01
0.083,0.073 0.292,0.25 0.208,0.177 10 false *a 0.469,1.938 0.875,2.104 0.406,0.167 10 false C138

a.

Disconnect the purge VSV connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C138-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Purge VSV)


c.

Reconnect the purge VSV connector.



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance between the terminals of the wire harness side connectors.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C138-2 - C37-10 (PRG) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C138-2 - C36-18 (PRG) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C138-2 or C37-10 (PRG) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C138-2 or C36-18 (PRG) - Body ground Always 10 kΩ or higher



d.

Reconnect the purge VSV connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
a.

Disconnect the purge VSV connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C138-1 - 1B-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C138-1 or 1B-4 - Body ground Always 10 kΩ or higher



d.

Reconnect the purge VSV connector.


e.

Reinstall the No. 1 integration relay.



OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT COMPONENTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR