Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal switch conditions are as shown in the table below.

Signal Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) are met for 0.5 seconds or more (1 trip detection logic):
(a) The engine switch is on (IG).
(b) The brake pedal is released.
(c) The STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM



WIRING DIAGRAM

for Automatic Transmission

A353967E02
5.104,0.417 5.208,0.563 0.104,0.146 10 false 2 4.854,0.51 5.125,0.698 0.271,0.188 10 false L 4.854,0.958 5.125,1.156 0.271,0.198 10 false L 4.521,0.51 4.792,0.688 0.271,0.177 10 false B 4.521,1.25 4.938,1.438 0.417,0.188 10 false GND 4.521,0.958 4.792,1.135 0.271,0.177 10 false B 4.302,0.417 4.406,0.563 0.104,0.146 10 false 1 5.104,0.865 5.208,1.01 0.104,0.146 10 false 4 4.302,1.135 4.406,1.281 0.104,0.146 10 false 3 4.302,0.865 4.406,1.01 0.104,0.146 10 false 5 4.281,1.708 5.396,1.896 1.115,0.188 10 false Stop Light Switch 4.281,1.573 4.615,1.719 0.333,0.146 10 false A85 6.313,1.969 6.667,2.135 0.354,0.167 10 false ECM 6.052,0.51 6.375,0.688 0.323,0.177 10 false STP 6.052,0.938 6.406,1.125 0.354,0.188 10 false ST1- 5.76,0.354 5.958,0.5 0.198,0.146 10 false 35 5.76,0.792 5.958,0.938 0.198,0.146 10 false 34 5.719,0.552 6,0.719 0.281,0.167 10 false G56 5.719,0.99 6,1.156 0.281,0.167 10 false G56 1.104,0.698 1.521,0.875 0.417,0.177 10 false STOP 2.5,1.125 2.792,1.302 0.292,0.177 10 false IGN 3.771,2.792 4.01,2.958 0.24,0.167 10 false 1A 3.521,2.146 3.76,2.313 0.24,0.167 10 false 1A 2.542,3.063 2.781,3.229 0.24,0.167 10 false 1A 1.469,2.438 1.708,2.604 0.24,0.167 10 false 1C 0.531,1.25 0.813,1.417 0.281,0.167 10 false ALT 0.729,2.615 1.094,2.781 0.365,0.167 10 false P/I-B 2.188,2.26 2.448,2.427 0.26,0.167 10 false IG2 3.021,3.01 3.281,3.177 0.26,0.167 10 false IG2 0.635,3.969 1.125,4.167 0.49,0.198 10 false Battery 4.104,2.333 5.573,2.51 1.469,0.177 10 false No. 1 Integration Relay 3.823,2.594 3.938,2.771 0.115,0.177 10 false 3 3.823,2.156 3.938,2.333 0.115,0.177 10 false 5 2.365,3.021 2.479,3.198 0.115,0.177 10 false 1 1.51,2.229 1.625,2.406 0.115,0.177 10 false 1 2.479,3.844 2.854,4.01 0.375,0.167 10 false IG2D 2.5,3.604 2.625,3.781 0.125,0.177 10 false 8 3.031,3.896 3.323,4.063 0.292,0.167 10 false G50 3.031,4.031 5.167,4.219 2.135,0.188 10 false Power Management Control ECU

for Manual Transmission

A353967E01
5.104,0.417 5.208,0.563 0.104,0.146 10 false 2 4.854,0.51 5.125,0.698 0.271,0.188 10 false L 4.854,0.958 5.125,1.156 0.271,0.198 10 false L 4.521,0.51 4.792,0.688 0.271,0.177 10 false B 4.521,1.25 4.938,1.438 0.417,0.188 10 false GND 4.521,0.958 4.792,1.135 0.271,0.177 10 false B 4.302,0.417 4.406,0.563 0.104,0.146 10 false 1 5.104,0.865 5.208,1.01 0.104,0.146 10 false 4 4.302,1.135 4.406,1.281 0.104,0.146 10 false 3 4.302,0.865 4.406,1.01 0.104,0.146 10 false 5 4.281,1.708 5.396,1.896 1.115,0.188 10 false Stop Light Switch 4.281,1.573 4.615,1.719 0.333,0.146 10 false A85 6.313,1.969 6.667,2.135 0.354,0.167 10 false ECM 6.052,0.51 6.375,0.688 0.323,0.177 10 false STP 6.052,0.938 6.406,1.125 0.354,0.188 10 false ST1- 5.75,0.344 5.948,0.49 0.198,0.146 10 false 18 5.802,0.802 5.917,0.948 0.115,0.146 10 false 8 5.719,0.552 6,0.719 0.281,0.167 10 false G56 5.719,0.99 6,1.156 0.281,0.167 10 false G55 1.104,0.698 1.521,0.875 0.417,0.177 10 false STOP 2.5,1.125 2.792,1.302 0.292,0.177 10 false IGN 3.771,2.792 4.01,2.958 0.24,0.167 10 false 1A 3.521,2.135 3.76,2.302 0.24,0.167 10 false 1A 2.542,3.063 2.781,3.229 0.24,0.167 10 false 1A 1.469,2.438 1.708,2.604 0.24,0.167 10 false 1C 0.531,1.25 0.813,1.417 0.281,0.167 10 false ALT 0.729,2.615 1.094,2.781 0.365,0.167 10 false P/I-B 2.188,2.26 2.448,2.427 0.26,0.167 10 false IG2 3.021,3 3.281,3.167 0.26,0.167 10 false IG2 0.635,3.969 1.125,4.167 0.49,0.198 10 false Battery 4.104,2.333 5.573,2.51 1.469,0.177 10 false No. 1 Integration Relay 3.823,2.594 3.938,2.771 0.115,0.177 10 false 3 3.823,2.156 3.938,2.333 0.115,0.177 10 false 5 2.365,3.021 2.479,3.198 0.115,0.177 10 false 1 1.51,2.229 1.625,2.406 0.115,0.177 10 false 1 2.479,3.844 2.854,4.01 0.375,0.167 10 false IG2D 2.5,3.604 2.625,3.781 0.125,0.177 10 false 8 3.031,3.896 3.323,4.063 0.292,0.167 10 false G50 3.031,4.031 5.167,4.219 2.135,0.188 10 false Power Management Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

(e)

Check the STP signal when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed STP signal ON
Released STP signal OFF

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
U149408E01
0.587,1.151 0.863,1.306 0.276,0.156 10 A85 0.116,0.072 0.385,0.261 0.269,0.189 10 *a 2.224,1.866 2.387,2.029 0.163,0.163 10 B 2.051,1.402 2.263,1.866 false 1.141,1.866 1.304,2.029 0.163,0.163 10 B 1.398,1.402 1.215,1.866 false

a.

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-1 (B) - Body ground Always 11 to 14 V
A85-5 (B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch)


c.

Reconnect the stop light switch connector.



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-3 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the stop light switch assembly connector.



OK

3.CHECK ECM (STP AND ST1 - VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (STP AND ST1 - VOLTAGE)
U169160E01
0.76,3.198 1.656,2.594 false 0.667,3.198 0.25,3.875 false 0.813,3.385 1.24,3.865 false 0.865,3.385 2.135,3.865 false 0.052,0.458 0.313,0.635 0.26,0.177 10 false *a 1.594,0.458 1.833,0.698 0.24,0.24 10 false *b 0.042,2.063 0.219,2.25 0.177,0.188 10 false *c 0.365,2.667 0.677,2.875 0.313,0.208 10 false G55 0.802,2.667 1.115,2.875 0.313,0.208 10 false G56 1.698,2.49 2.469,2.667 0.771,0.177 10 false 18 (STP)*B 0.167,3.885 0.896,4.063 0.729,0.177 10 false 8 (ST1-)*B 1.177,3.885 1.938,4.063 0.76,0.177 10 false 35 (STP)*A 2.167,3.865 2.99,4.042 0.823,0.177 10 false 34 (ST1-)*A

a.

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Automatic Transmission
Tester Connection Condition Specified Condition
G56-34 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed 0 to 3 V
G56-35 (STP) - Body ground Brake pedal released 0 to 3 V
Brake pedal depressed 11 to 14 V

for Manual Transmission
Tester Connection Condition Specified Condition
G55-8 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed 0 to 3 V
G56-18 (STP) - Body ground Brake pedal released 0 to 3 V
Brake pedal depressed 11 to 14 V


Text in Illustration
*A for Automatic Transmission
*B for Manual Transmission
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)



OK

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
A85-2 (L) - G56-35 (STP) Always Below 1 Ω
A85-4 (L) - G56-34 (ST1-) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
A85-2 (L) - G56-18 (STP) Always Below 1 Ω
A85-4 (L) - G55-8 (ST1-) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
A85-2 (L) or G56-35 (STP) - Body ground Always 10 kΩ or higher
A85-4 (L) or G56-34 (ST1-) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
A85-2 (L) or G56-18 (STP) - Body ground Always 10 kΩ or higher
A85-4 (L) or G55-8 (ST1-) - Body ground Always 10 kΩ or higher



d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the ECM connector.



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR