While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0617 | Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).
(a) The vehicle speed is 20 km/h (12.4 mph) or more. (b) The engine speed is 1000 rpm or more. (c) The STA signal is on. |
·
Park/neutral position switch assembly ·
Clutch pedal switch assembly ·
Starter relay circuit ·
ECM |
The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
If the engine will not crank, proceed to the Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the GTS when the engine switch is turned to on (IG) and when the engine is started.
| Condition | Display (Starter Signal) |
|---|---|
| Engine switch on (IG) | OFF |
| Engine is started | ON |
| Result | Proceed to |
|---|---|
| NG (for Automatic transmission) | A |
| NG (for Manual transmission) | B |
| OK | C |
A
B
C
Inspect the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Replace the park/neutral position switch assembly (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL).
NEXT
Check the clutch switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Replace the clutch switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the GTS when the engine switch is turned to on (IG) and when the engine is started.
| Condition | Display (Starter Signal) |
|---|---|
| Engine switch on (IG) | OFF |
| Engine is started | ON |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
for Automatic Transmission:
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C159-5 - G56-28 (STA) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C159-5 or G56-28 (STA) - Body ground | Always | 10 kΩ or higher |
Reconnect the park/neutral position switch assembly connector.
Reconnect the ECM connector.
for Manual Transmission:
Disconnect the clutch pedal switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-1 - G56-10 (STA) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-1 or G56-10 (STA) - Body ground | Always | 10 kΩ or higher |
Reconnect the clutch pedal switch connector.
Reconnect the ECM connector.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Drive the vehicle at more than 20 km/h (12.4 mph) for more than 20 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0617 | A |
| No DTC | B |
A
B