Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.

The accelerator pedal position sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.


A112620E33
0.173,3.81 2.506,4.019 2.333,0.209 10 Accelerator Pedal Sensor 0.759,0.75 1.239,0.932 0.480,0.181 10 Magnet 1.214,1.297 1.741,1.478 0.526,0.181 10 No. 1 IC 1.081,1.02 1.608,1.201 0.526,0.181 10 No. 2 IC 2.067,1.739 2.362,1.921 0.295,0.181 10 VPA 2.067,2.071 2.362,2.252 0.295,0.181 10 EPA 2.067,2.393 2.462,2.574 0.395,0.181 10 VCPA 2.067,2.687 2.439,2.869 0.372,0.181 10 VPA2 2.067,3.005 2.439,3.186 0.372,0.181 10 EPA2 2.067,3.327 2.447,3.508 0.380,0.181 10 VCP2 2.693,1.392 3.018,1.574 0.326,0.181 10 ECM 4.267,1.548 4.423,1.729 0.156,0.181 10 *1 5.864,1.548 6.020,1.729 0.156,0.181 10 *2 3.938,1.842 4.225,2.023 0.287,0.181 10 4.55 3.86,2.047 4.225,2.229 0.365,0.181 10 3.988 3.938,2.253 4.225,2.434 0.287,0.181 10 3.75 3.86,2.458 4.225,2.640 0.365,0.181 10 3.188 3.991,2.823 4.201,3.004 0.210,0.181 10 1.6 3.991,3.042 4.201,3.223 0.210,0.181 10 0.8 4.411,3.346 4.698,3.527 0.287,0.181 10 0.29 4.259,3.596 4.415,3.777 0.156,0.181 10 0 5.784,3.596 6.071,3.777 0.287,0.181 10 15.9 4.682,3.587 5.606,3.827 0.924,0.239 10 Usable Range 4.369,4.054 6.867,4.257 2.498,0.202 10 Accelerator Pedal Angle (°) 4.369,4.391 6.648,4.572 2.279,0.181 10 *1: Accelerator Pedal Fully Released 4.369,4.727 6.756,4.892 2.387,0.165 10 *2: Accelerator Pedal Fully Depressed 4.355,2.014 4.234,1.93 false 4.346,2.182 4.234,2.126 false 4.346,2.228 4.234,2.322 false 4.346,2.397 4.234,2.518 false 4.346,2.901 4.215,2.901 false 4.355,3.116 4.206,3.116 false 0.686,3.387 1.166,3.568 0.480,0.181 10 Magnet 0.843,2.878 0.975,1.099 0.975,1.099 1.062,1.099 false 1.74,0.629 3.947,0.954 2.207,0.325 10 Accelerator Pedal Position Sensor Output Voltage (V) 4.355,1.965 3.925,0.728 false 0.847,2.267 0.649,0.827 0.649,0.827 0.752,0.827 false 1.068,2.561 1.068,1.37 1.068,1.37 1.179,1.37 false 0.843,3.103 0.605,3.461 0.605,3.461 0.679,3.461 false

DTC No. DTC Detection Condition Trouble Area
P2120 VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor

·

ECM


P2122 VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator pedal position sensor

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


P2123 VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor

·

Open in EPA circuit

·

ECM


P2125 VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor

·

ECM


P2127 VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator pedal position sensor

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


P2128 Conditions (a) and (b) are met for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

Accelerator pedal position sensor

·

Open in EPA2 circuit

·

ECM


P2138 Condition (a) or (b) is met for 2.0 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less.
·

Short between VPA and VPA2 circuits

·

Accelerator pedal position sensor

·

ECM



HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage by entering the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Accel Sensor Out No. 1 and Accel Sensor Out No. 2

Trouble Area Accel Sensor Out No. 1
When Accelerator Pedal Released
Accel Sensor Out No. 2
When Accelerator Pedal Released
Accel Sensor Out No. 1
When Accelerator Pedal Depressed
Accel Sensor Out No. 2
When Accelerator Pedal Depressed
VCP circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
EPA circuit open 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When the output voltage of either VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is below the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA drops below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.

If the malfunction is not repaired successfully, a DTC is stored 2 seconds after the engine is next started.

FAIL-SAFE

When of DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles

The ECM continues operating fail-safe mode until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

for Automatic Transmission

A353968E01
0.271,3.24 2.427,3.448 2.156,0.208 10 false Accelerator Pedal Position Sensor 1.542,0.542 2.01,0.75 0.469,0.208 10 false VPA 1.542,0.969 2.01,1.177 0.469,0.208 10 false EPA 1.448,1.375 2.031,1.583 0.583,0.208 10 false VCPA 1.479,1.781 2.063,1.99 0.583,0.208 10 false VPA2 1.479,2.188 2.063,2.396 0.583,0.208 10 false EPA2 1.479,2.625 2.063,2.833 0.583,0.208 10 false VCP2 5.594,0.406 5.99,0.615 0.396,0.208 10 false VPA 5.219,0.563 5.615,0.771 0.396,0.208 10 false G55 5.219,0.979 5.615,1.188 0.396,0.208 10 false G55 5.219,1.396 5.615,1.604 0.396,0.208 10 false G56 5.219,1.813 5.615,2.021 0.396,0.208 10 false G56 5.219,2.24 5.615,2.448 0.396,0.208 10 false G56 5.219,2.646 5.615,2.854 0.396,0.208 10 false G56 5.313,0.354 5.49,0.563 0.177,0.208 10 false 2 5.313,0.781 5.49,0.99 0.177,0.208 10 false 1 5.313,1.188 5.49,1.396 0.177,0.208 10 false 6 5.313,1.615 5.49,1.823 0.177,0.208 10 false 5 5.313,2.031 5.49,2.24 0.177,0.208 10 false 4 5.313,2.458 5.49,2.667 0.177,0.208 10 false 3 5.594,0.813 5.99,1.021 0.396,0.208 10 false EPA 5.594,1.26 6.042,1.469 0.448,0.208 10 false VCPA 5.594,1.688 6.042,1.896 0.448,0.208 10 false VPA2 5.594,2.094 6.031,2.302 0.438,0.208 10 false EPA2 5.594,2.51 6.177,2.719 0.583,0.208 10 false VCP2 1.958,0.396 2.167,0.604 0.208,0.208 10 false 6 1.958,0.823 2.167,1.031 0.208,0.208 10 false 5 1.958,1.25 2.167,1.458 0.208,0.208 10 false 4 1.958,1.667 2.167,1.875 0.208,0.208 10 false 3 1.958,2.094 2.167,2.302 0.208,0.208 10 false 2 1.958,2.51 2.167,2.719 0.208,0.208 10 false 1 6,3.073 6.396,3.271 0.396,0.198 10 false ECM 0.271,3.073 0.552,3.26 0.281,0.188 10 false A19

for Manual Transmission

A149601E44
0.281,3.219 2.438,3.427 2.156,0.208 10 false Accelerator Pedal Position Sensor 1.573,0.531 2.042,0.74 0.469,0.208 10 false VPA 1.563,0.948 2.031,1.156 0.469,0.208 10 false EPA 1.469,1.354 2.052,1.563 0.583,0.208 10 false VCPA 1.49,1.781 2.073,1.99 0.583,0.208 10 false VPA2 1.49,2.188 2.073,2.396 0.583,0.208 10 false EPA2 1.49,2.615 2.073,2.823 0.583,0.208 10 false VCP2 5.604,0.396 6,0.604 0.396,0.208 10 false VPA 5.417,0.635 5.594,0.844 0.177,0.208 10 false 6 5.417,1.052 5.594,1.26 0.177,0.208 10 false 3 5.417,1.469 5.594,1.677 0.177,0.208 10 false 4 5.417,1.885 5.594,2.094 0.177,0.208 10 false 5 5.417,2.313 5.594,2.521 0.177,0.208 10 false 1 5.417,2.74 5.594,2.948 0.177,0.208 10 false 2 5.604,0.802 6,1.01 0.396,0.208 10 false EPA 5.604,1.25 6.052,1.458 0.448,0.208 10 false VCPA 5.604,1.667 6.052,1.875 0.448,0.208 10 false VPA2 5.604,2.083 6.042,2.292 0.438,0.208 10 false EPA2 5.604,2.5 6.188,2.708 0.583,0.208 10 false VCP2 1.99,0.615 2.198,0.823 0.208,0.208 10 false 6 1.99,1.042 2.198,1.25 0.208,0.208 10 false 5 1.99,1.458 2.198,1.667 0.208,0.208 10 false 4 1.99,1.885 2.198,2.094 0.208,0.208 10 false 3 1.99,2.302 2.198,2.51 0.208,0.208 10 false 2 1.99,2.729 2.198,2.938 0.208,0.208 10 false 1 5.979,3.219 6.375,3.417 0.396,0.198 10 false ECM 5.979,3.042 6.854,3.219 0.875,0.177 10 false G56 0.281,3.063 0.563,3.25 0.281,0.188 10 false A19

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the accelerator pedal position sensor.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR)
FI07052E38
0.662,1.77 0.888,1.971 0.226,0.201 10 *a 2.604,1.77 2.797,1.971 0.193,0.201 10 *b 2.861,2.02 3.414,2.153 0.553,0.134

a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


d.

Read the value displayed on the GTS.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V
Depressed 2.6 to 4.5 V 3.4 to 4.75 V


Text in Illustration
*a Depressed
*b Released

Result
Result Proceed to
OK A
NG B



B

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

A

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
A19-6 (VPA) - G55-2 (VPA) Always Below 1 Ω
A19-5 (EPA) - G55-1 (EPA) Always Below 1 Ω
A19-4 (VCPA) - G56-6 (VCPA) Always Below 1 Ω
A19-3 (VPA2) - G56-5 (VPA2) Always Below 1 Ω
A19-2 (EPA2) - G56-4 (EPA2) Always Below 1 Ω
A19-1 (VCP2) - G56-3 (VCP2) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
A19-6 (VPA) - G56-6 (VPA) Always Below 1 Ω
A19-5 (EPA) - G56-3 (EPA) Always Below 1 Ω
A19-4 (VCPA) - G56-4 (VCPA) Always Below 1 Ω
A19-3 (VPA2) - G56-5 (VPA2) Always Below 1 Ω
A19-2 (EPA2) - G56-1 (EPA2) Always Below 1 Ω
A19-1 (VCP2) - G56-2 (VCP2) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
A19-6 (VPA) or G55-2 (VPA) - Body ground Always 10 kΩ or higher
A19-5 (EPA) or G55-1 (EPA) - Body ground Always 10 kΩ or higher
A19-4 (VCPA) or G56-6 (VCPA) - Body ground Always 10 kΩ or higher
A19-3 (VPA2) or G56-5 (VPA2) - Body ground Always 10 kΩ or higher
A19-2 (EPA2) or G56-4 (EPA2) - Body ground Always 10 kΩ or higher
A19-1 (VCP2) or G56-3 (VCP2) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
A19-6 (VPA) or G56-6 (VPA) - Body ground Always 10 kΩ or higher
A19-5 (EPA) or G56-3 (EPA) - Body ground Always 10 kΩ or higher
A19-4 (VCPA) or G56-4 (VCPA) - Body ground Always 10 kΩ or higher
A19-3 (VPA2) or G56-5 (VPA2) - Body ground Always 10 kΩ or higher
A19-2 (EPA2) or G56-1 (EPA2) - Body ground Always 10 kΩ or higher
A19-1 (VCP2) or G56-2 (VCP2) - Body ground Always 10 kΩ or higher



d.

Reconnect the accelerator pedal position sensor connector.


e.

Reconnect the ECM connector.



OK

3.CHECK ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (VCPA AND VCP2 VOLTAGE)
U147509E02
1.354,1.135 0.74,1.677 false 1.49,1.125 1.365,1.667 false 1.76,1.135 1.99,1.646 false 1.896,1.125 2.625,1.667 false 0.479,0.99 0.74,1.167 0.26,0.177 10 false A19 1.135,1.698 1.531,1.875 0.396,0.177 10 false EPA2 1.833,1.698 2.229,1.875 0.396,0.177 10 false VCPA 0.385,1.698 0.76,1.875 0.375,0.177 10 false VCP2 0.094,0.031 0.25,0.208 0.156,0.177 10 false *a 2.573,1.688 2.927,1.865 0.354,0.177 10 false EPA

a.

Disconnect the accelerator pedal position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A19-4 (VCPA) - A19-5 (EPA) Engine switch on (IG) 4.5 to 5.5 V
A19-1 (VCP2) - A19-2 (EPA2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


c.

Reconnect the accelerator pedal position sensor connector.



OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine.


e.

Allow the engine to idle for 15 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 A
No output B



A

B

SYSTEM OK