Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injector assemblies are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)
U147528E03
0.156,0 0.344,0.146 0.188,0.146 10 false *a 0.156,0.823 0.438,0.969 0.281,0.146 10 false C1 0.583,0.823 0.865,0.969 0.281,0.146 10 false C2 0.146,1.167 0.427,1.313 0.281,0.146 10 false C3 0.594,1.167 0.875,1.313 0.281,0.146 10 false C4 0.156,1.5 0.438,1.646 0.281,0.146 10 false C5 0.594,1.51 0.875,1.656 0.281,0.146 10 false C6

a.

Disconnect the fuel injector assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C1-1 - Body ground Engine switch on (IG) 11 to 14 V
C2-1 - Body ground Engine switch on (IG) 11 to 14 V
C3-1 - Body ground Engine switch on (IG) 11 to 14 V
C4-1 - Body ground Engine switch on (IG) 11 to 14 V
C5-1 - Body ground Engine switch on (IG) 11 to 14 V
C6-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Injector Assembly)


c.

Reconnect the fuel injector assembly connector.



OK

2.INSPECT FUEL INJECTOR ASSEMBLY

NG

4.INSPECT NO. 1 INTEGRATION RELAY (IG2)
2.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the fuel injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C1-2 - C37-6 (#10) Always Below 1 Ω
C2-2 - C37-1 (#20) Always Below 1 Ω
C3-2 - C37-7 (#30) Always Below 1 Ω
C4-2 - C37-2 (#40) Always Below 1 Ω
C5-2 - C37-8 (#50) Always Below 1 Ω
C6-2 - C37-3 (#60) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C1-2 or C37-6 (#10) - Body ground Always 10 kΩ or higher
C2-2 or C37-1 (#20) - Body ground Always 10 kΩ or higher
C3-2 or C37-7 (#30) - Body ground Always 10 kΩ or higher
C4-2 or C37-2 (#40) - Body ground Always 10 kΩ or higher
C5-2 or C37-8 (#50) - Body ground Always 10 kΩ or higher
C6-2 or C37-3 (#60) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel injector assembly connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NO. 1 INTEGRATION RELAY (IG2)
a.

Inspect the No. 1 integration relay (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2)