Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL INJECTOR
RM27T0E _51 Engine / Hybrid System _053667 1GR-FE FUEL _0260543 FUEL INJECTOR G

1GR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the injector assembly.


Hide 23250 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.

Check the injector injection.

CAUTION:
·

This test involves high-pressure fuel and electricity.

·

Take every precaution regarding safe handling of both the fuel and the electrical parts.

·

Perform this test in a safe area and avoid any sparks or flame.

·

Do not smoke.



i.
A273742E02
0.552,0.865 0.448,0.865 0.448,0.865 0.365,1.24 false 1.135,1.635 1.135,1.583 1.135,1.583 1,1.49 false 2.177,0.219 2.177,0.135 false 2.177,0.135 1.26,0.135 false 1.833,0.417 1.833,0.135 false 2.01,1.729 1.823,1.729 false 2.427,1.625 2.354,1.625 2.354,1.625 2.323,1.771 false 2.031,2.323 1.646,2.323 false 3.229,2.354 3.073,2.354 false 3.198,1.26 3.125,1.26 3.125,1.26 2.906,1.656 false 3.083,0.469 2.885,0.469 false 2.49,0.771 2.49,0.688 2.49,0.688 2.125,0.427 false 1.885,0.688 1.781,0.688 1.781,0.688 1.781,1.365 false 1.781,1.219 1.885,1.219 false 0.896,0.552 1.021,0.552 1.021,0.552 1.208,1.052 false 2.448,1.208 2.552,1.208 2.552,1.208 2.646,1.396 false 1.052,1.656 1.229,1.813 0.177,0.156 10 false *2 0.583,0.781 0.76,0.938 0.177,0.156 10 false *1 3.229,2.26 3.406,2.417 0.177,0.156 10 false *9 1.448,2.25 1.625,2.406 0.177,0.156 10 false *8 2.438,1.542 2.615,1.698 0.177,0.156 10 false *7 1.604,1.646 1.781,1.802 0.177,0.156 10 false *6 3.104,0.385 3.281,0.542 0.177,0.156 10 false *5 3.219,1.177 3.396,1.333 0.177,0.156 10 false *4 1.063,0.052 1.24,0.208 0.177,0.156 10 false *3 2.333,0.792 2.583,0.948 0.25,0.156 10 false *10 1.667,1.365 1.844,1.521 0.177,0.156 10 false *3 0.698,0.448 0.875,0.604 0.177,0.156 10 false *3 2.25,1.135 2.427,1.292 0.177,0.156 10 false *3

Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41091, 09268-41120, 09268-41141, 09268-41410, 09268-41500, 09268-41700, 95336-08070)

Text in Illustration
*1 Fuel Pressure Regulator
*2 SST (Union)
*3 SST (Hose Band)
*4 SST (Fuel Tube Connector)
*5 SST (Hose)
*6 SST (Adapter)
*7 SST (Clamp)
*8 Fuel Injector
*9 Fuel Filter
*10 SST (3 Way)


ii.

Discharge the fuel system pressure (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PRESSURE REGULATOR>REMOVAL).


iii.

Disconnect the fuel inlet hose (fuel tube connector) from the fuel pipe.


iv.

Remove the bolt and disconnect the fuel pressure regulator from the fuel delivery pipe.

NOTICE:

Do not disconnect the No. 2 fuel pipe from the fuel pressure regulator.



v.
A273743E01
1.661,1.237 1.832,1.414 0.171,0.177 10 *1 1.737,1.833 1.916,2.003 0.179,0.170 10 *2 1.854,1.323 2.008,1.323 2.008,1.323 2.282,0.897 false 1.939,1.925 2.094,1.925 2.094,1.925 2.348,1.666 false

Connect SST to the fuel pipe.

SST
09268-31014  (09268-41500)

Text in Illustration
*1 SST (Fuel Tube Connector)
*2 Fuel Filter

CAUTION:

Always read the precautions before connecting the fuel tube connector.



vi.
A273744E02
0.896,0.26 1,0.26 1,0.26 1.26,0.458 false 1.781,1.688 1.51,1.688 false 2.417,0.875 2.344,0.875 2.344,0.875 2.229,0.677 false 2.802,0.406 2.802,0.177 false 2.74,0.438 2.948,0.656 0.208,0.219 10 false *2 2.448,0.792 2.646,0.99 0.198,0.198 10 false *4 1.813,1.594 2.031,1.792 0.219,0.198 10 false *3 0.698,0.167 0.917,0.375 0.219,0.208 10 false *1

Connect SST (hose) to the fuel inlet of the pressure regulator with another SST (union) and the 2 bolts.

SST
09268-31014  (09268-41091, 95336-08070)

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

Text in Illustration
*1 Fuel Pressure Regulator
*2 SST (Hose)
*3 No. 2 Fuel Pipe Sub-assembly
*4 SST (Union)


vii.

Connect the fuel return hose to the fuel outlet of the pressure regulator.


viii.
A273745E01
0.311,0.885 0.495,1.051 0.184,0.166 10 *2 2.715,2.352 2.899,2.519 0.184,0.166 10 *6 1.448,2.579 1.631,2.745 0.184,0.166 10 *5 0.28,2.608 0.464,2.774 0.184,0.166 10 *4 2.511,0.627 2.695,0.794 0.184,0.166 10 *3 0.324,0.546 0.499,0.712 0.174,0.166 10 *1 0.521,0.63 0.722,0.63 false 0.517,0.976 0.68,0.976 false 0.407,2.595 0.407,2.492 0.407,2.492 0.694,2.326 false 1.654,2.659 1.854,2.659 false 2.83,2.338 2.83,2.252 2.83,2.252 2.61,1.985 false 2.497,0.711 2.414,0.711 2.414,0.711 2.15,1.003 false

Install a new O-ring to the injector.


ix.

Connect SST (adapter and hose) to the injector and hold the injector and adapter with SST (clamp).

SST
09268-31014  (09268-41141, 09268-41410, 09268-41700, 95336-08070)

Text in Illustration
*1 SST (Hose)
*2 SST (Hose Band)
*3 O-Ring
*4 SST (Adapter)
*5 Vinyl Tube
*6 SST (Clamp)


x.
A273746E01
1.854,1.877 2.036,2.044 0.183,0.166 10 *1 2.713,0.945 2.896,1.112 0.183,0.166 10 *a 1.852,1.968 1.712,1.968 1.712,1.968 1.511,1.627 false 2.709,1.054 2.574,1.054 2.574,1.054 2.425,0.805 false

Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

Text in Illustration
*1 SST (Tie Band)
*a Lock

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



xi.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


xii.

Put the injector into a graduated cylinder.

CAUTION:

Install a suitable vinyl tube to the injector to contain any gasoline spray.



xiii.

Connect the intelligent tester to the DLC3.


xiv.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



xv.

Turn the intelligent tester on.


xvi.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.


xvii.
A273747E01
1.738,0.87 1.922,1.040 0.184,0.170 10 *1 1.858,0.859 1.858,0.325 false

Connect SST (EFI inspection wire) to the injector and the battery for 15 seconds and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard injection volume:

89 to 107 cm3 (5.4 to 6.5 cu. in.) per 15 seconds


Difference between each injector:

15 cm3 (0.9 cu. in.) or less


Text in Illustration
*1 SST (EFI Inspection Wire)
V100135

Connect

NOTICE:
·

Make sure that SST (EFI inspection wire) is securely connected.

·

Always turn the voltage on and off the battery side, not the fuel pump side.



If the result is not as specified, replace the injector assembly.



b.

Check for fuel leakage.

i.

In the condition above, disconnect the tester probes of SST (EFI inspection wire) from the battery and check for fuel leakage from the injector.

Standard fuel leakage:

1 drop or less per 12 minutes


If the fuel leakage is not as specified, replace the injector assembly.