Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0014  Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)  P0015  Camshaft Position "B" - Timing Over-Retarded (Bank 1)  P0024  Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2)  P0025  Camshaft Position "B" - Timing Over-Retarded (Bank 2)  


DESCRIPTION

Refer to DTC P0013 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0013).

DTC No. DTC Detection Condition Trouble Area
P0014
P0024
Valve timing is not adjusted in valve timing advance range
(2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side of bank 1, 2)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


P0015
P0025
Valve timing is not adjusted in valve timing retard range
(1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust side of bank 1, 2)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
Abnormal Bank Timing Over-Advanced
(Valve timing is out of specified range)
Timing Over-Retarded
(Valve timing is out of specified range)
Bank 1 P0014 P0015
Bank 2 P0024 P0025

·

If DTC P0014 or P0015 is output, check the exhaust camshaft circuit for the right bank VVT system (bank 1).

·

Bank 1 refers to the bank that includes cylinder No. 1.

·

If DTC P0024 or P0025 is output, check the exhaust camshaft circuit for the left bank VVT system (bank 2).

·

Bank 2 refers to the bank that does not include cylinder No. 1.

·

DTC P0014, P0015, P0024 or P0025 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0014, P0015, P0024 or P0025 is output A
DTC P0014, P0015, P0024 or P0025 and other DTCs are output B

HINT:

If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 1 OR 2))

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 1 OR 2))
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).


e.

Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

OK:
GTS Operation Engine Condition
0% (OFF) Normal engine speed
127% (ON) Engine idles roughly or stalls soon after camshaft timing oil control valve assembly switched from off to on




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH OR WHETHER TIMING CHAIN HAS JUMPED TOOTH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Drive the vehicle for more than 10 minutes.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read the pending DTCs.

Result
Result Proceed to
No DTC is output A
DTC P0014, P0015, P0024 or P0025 is output B

HINT:

DTC P0014, P0015, P0024 or P0025 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.




A

B

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH OR WHETHER TIMING CHAIN HAS JUMPED TOOTH)
4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH OR WHETHER TIMING CHAIN HAS JUMPED TOOTH)
a.

Remove the cylinder head cover sub-assembly RH and LH.

A378871E01
1.573,1.833 1.969,1.333 1.969,1.333 1.594,2.021 false 2.385,1.833 2.052,2.427 2.052,2.427 2.354,2.125 false 4.969,1.083 5.365,0.646 5.365,0.646 4.979,1.406 false 5.688,1.167 5.354,1.76 5.354,1.76 5.729,1.344 false 5.698,1.313 5.385,1.719 false 1.99,1.177 2.302,1.375 0.313,0.198 10 false *a 1.917,2.438 2.135,2.615 0.219,0.177 10 false *a 5.406,0.49 5.719,0.688 0.313,0.198 10 false *a 5.25,1.771 5.563,1.969 0.313,0.198 10 false *a


b.

Turn the crankshaft to align the matchmarks of the crankshaft.


c.

Align the notch of the crankshaft pulley to the "0" position.


d.

Check if the timing marks of the camshaft pulley and camshaft bearing cap align.

Text in Illustration
*a Timing Mark


e.

Turn the crankshaft clockwise 360° if the timing marks do not align. Check if they align once again.

OK:

The timing marks of the camshaft pulley and camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.



f.

Reinstall the cylinder head cover sub-assembly RH and LH.



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)
a.

Inspect the camshaft timing oil control valve assembly (for exhaust side of bank 1, 2) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE
a.
A225778E02
0.048,0 0.246,0.177 0.198,0.177 10 *A 0.048,2.293 0.246,2.469 0.198,0.177 10 *B

Remove the No. 1 oil pipe or No. 2 oil pipe.


b.

Remove the oil control valve filter RH or oil control valve filter LH.


c.

Check that the oil control valve filter and oil pipe are not clogged.

OK:

The oil control valve filter and oil pipe are not clogged.


Text in Illustration
*A Bank 2
*B Bank 1


d.

Reinstall the oil control valve filter RH or oil control valve filter LH.


e.

Reinstall the No. 1 oil pipe or No. 2 oil pipe.



OK

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly (bank 1 or bank 2) (See page Engine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Drive the vehicle for more than 10 minutes.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read the pending DTCs.

Result
Result Proceed to
No DTC is output A
DTC P0014, P0015, P0024 and P0025 is output B



A

REPAIR COMPLETED

B