Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1)  P2238  Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2239  Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 1 Sensor 1)  P2240  Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 2 Sensor 1)  P2241  Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 2 Sensor 1)  P2242  Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 2 Sensor 1)  P2252  Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2253  Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 1 Sensor 1)  P2255  Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 2 Sensor 1)  P2256  Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 2 Sensor 1)  


DESCRIPTION

HINT:
·

Although the DTC titles say heated oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.



The air fuel ratio sensor, which is located between the exhaust manifold and catalyst, consists of alloyed metal elements and a heater.

Depending on the engine operating conditions, the heater heats the sensor elements to activate them. Battery voltage is applied to the heater and the sensor ground is controlled by the ECM using a duty ratio.

The sensor elements convert the oxygen concentration in the exhaust gas into voltage values to output. Based on the voltage, the ECM determines the air fuel ratio and regulates the fuel injection volume according on the air fuel ratio and engine operating conditions. The voltage changes between 0.5 V and 4.5 V while the engine is running. If the air fuel ratio is lean, which means the oxygen concentration in the exhaust gas is high, the voltage is high. If the air fuel ratio is rich, which means the oxygen concentration in the exhaust gas is low, the voltage is low.

A378866E02
0.135,0.146 3.302,0.375 3.167,0.229 10 false Reference (System Diagram of Bank 1 Sensor 1): 0.094,1.073 0.938,1.281 0.844,0.208 10 false from Battery 0.271,2.729 0.854,3.094 0.583,0.365 10 false from EFI Relay 2.24,2.188 2.563,2.365 0.323,0.177 10 false A/F 1.281,0.896 1.604,1.073 0.323,0.177 10 false A/F 3.438,0.969 3.688,1.146 0.25,0.177 10 false +B 3.292,1.635 3.677,1.833 0.385,0.198 10 false A1A- 4.458,0.969 4.896,1.156 0.438,0.188 10 false HA1A 4.469,1.656 4.906,1.844 0.438,0.188 10 false A1A+ 3.844,0.823 4.344,1.01 0.5,0.188 10 false Heater 3.844,1.438 4.344,1.625 0.5,0.188 10 false Sensor 3.719,2.115 4.51,2.313 0.792,0.198 10 false A/F Sensor 5.188,0.969 5.625,1.156 0.438,0.188 10 false HA1A 5.208,1.646 5.646,1.833 0.438,0.188 10 false A1A+ 5.208,2.292 5.594,2.49 0.385,0.198 10 false A1A- 5.896,0.323 6.333,0.51 0.438,0.188 10 false ECM 6.354,1.771 6.875,2.135 0.521,0.365 10 false Duty Control

A225212E01
3.052,2.583 3.385,2.896 false 2.844,2.365 3.354,2.552 false 2.979,2.01 3.365,1.938 false 3,2.302 3.354,2.552 false 3.188,1.833 3.333,1.469 3.333,1.469 3.375,1.469 false 1.781,2.573 2.063,2.573 false 1.594,2.625 0.99,2.24 0.99,2.24 0.948,2.24 false 1.125,3.083 1.25,3.281 0.125,0.198 10 false A 2.021,3.083 2.146,3.281 0.125,0.198 10 false A 0.406,2.146 0.948,2.302 0.542,0.156 10 false Element 0.094,2.958 0.979,3.177 0.885,0.219 10 false Exhaust Gas 2.698,3.156 3.49,3.375 0.792,0.219 10 false A-A Section 3.417,2.469 4.625,2.688 1.208,0.219 10 false Platinum Electrode 2.094,2.479 2.656,2.698 0.563,0.219 10 false Cover 3.417,2.833 3.708,3.031 0.292,0.198 10 false Air 3.438,1.385 3.875,1.604 0.438,0.219 10 false Heater 3.406,1.771 4.594,2.156 1.188,0.385 10 false Solid Electrolyte (Zirconia Element) 5.156,3.094 6.865,3.313 1.708,0.219 10 false Rich - Air-fuel Ratio - Lean 5.771,0.417 7.125,0.635 1.354,0.219 10 false Ideal Air-Fuel Mixture 4.354,0.615 5.344,0.823 0.99,0.208 10 false Output Voltage 4.698,0.99 4.917,1.198 0.219,0.208 10 false (V) 4.677,2.552 4.896,2.708 0.219,0.156 10 false 2.4 4.677,2.396 4.896,2.552 0.219,0.156 10 false 2.6 4.677,2.229 4.896,2.385 0.219,0.156 10 false 2.8 4.677,2.073 4.896,2.229 0.219,0.156 10 false 3.0 4.677,1.906 4.896,2.063 0.219,0.156 10 false 3.2 4.677,1.75 4.896,1.906 0.219,0.156 10 false 3.4 4.677,1.583 4.896,1.74 0.219,0.156 10 false 3.6 4.677,1.427 4.896,1.583 0.219,0.156 10 false 3.8 4.677,1.26 4.896,1.417 0.219,0.156 10 false 4.0 5.094,2.823 5.292,2.99 0.198,0.167 10 false 12 5.323,2.823 5.521,2.99 0.198,0.167 10 false 13 5.552,2.823 5.75,2.99 0.198,0.167 10 false 14 5.792,2.823 5.99,2.99 0.198,0.167 10 false 15 6.021,2.823 6.219,2.99 0.198,0.167 10 false 16 6.25,2.823 6.448,2.99 0.198,0.167 10 false 17 6.479,2.823 6.677,2.99 0.198,0.167 10 false 18 6.708,2.823 6.906,2.99 0.198,0.167 10 false 19

DTC No. DTC Detection Condition Trouble Area
P2237
P2240
An open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2238
P2241
Any of the following conditions are met (2 trip detection logic):
·

The air fuel ratio sensor output drops while the engine is running.

·

The voltage at terminal A1A+/A2A+ is 0.5 V or less.

·

The voltage difference between terminals A1A+/A2A+ and A1A-/A2A- is 0.1 V or less.


·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2239
P2242
The A1A+/A2A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2252
P2255
The A1A-/A2A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM


P2253
P2256
The A1A-/A2A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM



MONITOR DESCRIPTION

These DTCs are stored when there is an open or short in the air fuel ratio sensor circuit, or if the air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the engine switch on (IG), and the admittance (admittance is an electrical term that indicates the ease of current flow) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.5 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in the next driving cycle, the MIL will be illuminated and a DTC will be stored.

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" step of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor. This is useful for verifying the completion of the repair.



A172863E06
0.687,0.396 1.641,0.599 0.954,0.203 10 Vehicle Speed 0.564,2.592 1.835,2.795 1.272,0.203 10 Engine Switch Off 4.778,2.764 5.278,2.967 0.500,0.203 10 Time 1.265,2.232 1.658,2.435 0.393,0.203 10 Idling 0.205,0.873 1.592,1.440 1.387,0.567 10 Between 60 km/h and 120 km/h (37 mph and 75 mph) 2.35,2.104 2.578,2.307 0.228,0.203 10 (A) 3.852,0.719 4.079,0.922 0.228,0.203 10 (B) 2.189,2.796 2.818,2.999 0.629,0.203 10 Warmup 3.422,2.882 4.152,3.085 0.730,0.203 10 10 Minutes 1.56,3.239 6.017,3.442 4.457,0.203 10 (Note: Even if vehicle stops during driving pattern, test can be resumed) 4.937,0.115 5.584,0.317 0.647,0.202 10 NOTICE: 4.937,0.461 7.050,1.158 2.114,0.697 10 This test will not be completed if the vehicle is driven at absolutely constant speed, such as with cruise control activated.

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

5.

Switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE).

6.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S (A/FS) Monitor.

7.

Check that the item O2S (A/FS) Monitor displays Incmpl (incomplete).

8.

Start the engine and warm it up. (A)

9.

Drive the vehicle at between 60 km/h and 120 km/h (37 mph and 75 mph) for at least 10 minutes. (B)

10.

Note the state of the Data List items. Those items will change to Compl (complete) as the heated oxygen sensor monitor operates.

11.

On the GTS, enter the following menus: Powertrain / Engine and ECT / Trouble Codes; and check if any DTCs (any pending DTCs) are output.


HINT:

If the item O2S (A/FS) Monitor does not change to Compl (complete) and any pending DTCs fail to be stored, extend the driving time.


CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for air fuel ratio sensor function provided in the Active Test. The Control the Injection Volume for air fuel ratio sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

On the GTS, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for air fuel ratio sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E50
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.469,1.604 1.917,1.792 0.448,0.188 8 false +12.5% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.135 6.885,6.563 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leakage from exhaust system (air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.417,3.677 1.865,3.865 0.448,0.188 8 false +12.5% 4.01,1.594 4.458,1.781 0.448,0.188 8 false +12.5% 4,3.667 4.448,3.854 0.448,0.188 8 false +12.5% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.406,5.75 1.854,5.938 0.448,0.188 8 false +12.5% 1.375,7.771 1.823,7.958 0.448,0.188 8 false +12.5% 4.031,7.792 4.479,7.979 0.448,0.188 8 false +12.5% 4.073,5.729 4.521,5.917 0.448,0.188 8 false +12.5% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for air fuel ratio sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C25-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C26-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C37-17 (HA1A) Always Below 1 Ω
C25-3 (A1A+) - C35-7 (A1A+) Always Below 1 Ω
C25-4 (A1A-) - C35-8 (A1A-) Always Below 1 Ω
C26-1 (HA2A) - C37-12 (HA2A) Always Below 1 Ω
C26-3 (A2A+) - C35-1 (A2A+) Always Below 1 Ω
C26-4 (A2A-) - C35-2 (A2A-) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C37-17 (HA1A) Always Below 1 Ω
C25-3 (A1A+) - C36-1 (A1A+) Always Below 1 Ω
C25-4 (A1A-) - C36-2 (A1A-) Always Below 1 Ω
C26-1 (HA2A) - C37-19 (HA2A) Always Below 1 Ω
C26-3 (A2A+) - C36-7 (A2A+) Always Below 1 Ω
C26-4 (A2A-) - C36-8 (A2A-) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) or C37-17 (HA1A) - Body ground Always 10 kΩ or higher
C25-3 (A1A+) or C35-7 (A1A+) - Body ground Always 10 kΩ or higher
C25-4 (A1A-) or C35-8 (A1A-) - Body ground Always 10 kΩ or higher
C26-1 (HA2A) or C37-12 (HA2A) - Body ground Always 10 kΩ or higher
C26-3 (A2A+) or C35-1 (A2A+) - Body ground Always 10 kΩ or higher
C26-4 (A2A-) or C35-2 (A2A-) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) or C37-17 (HA1A) - Body ground Always 10 kΩ or higher
C25-3 (A1A+) or C36-1 (A1A+) - Body ground Always 10 kΩ or higher
C25-4 (A1A-) or C36-2 (A1A-) - Body ground Always 10 kΩ or higher
C26-1 (HA2A) or C37-19 (HA2A) - Body ground Always 10 kΩ or higher
C26-3 (A2A+) or C36-7 (A2A+) - Body ground Always 10 kΩ or higher
C26-4 (A2A-) or C36-8 (A2A-) - Body ground Always 10 kΩ or higher



g.

Reconnect the air fuel ratio sensor connector.


h.

Reconnect the ECM connector.



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

3.PERFORM CONFIRMATION DRIVING PATTERN
3.PERFORM CONFIRMATION DRIVING PATTERN

NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine.


e.

Allow the engine to idle for 5 minutes or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read the pending DTCs.

Result
Result Proceed to
No output A
P2237, P2240, P2238, P2241, P2239, P2242, P2252, P2255, P2253 or P2256 output B



A

END

B