Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  P2197  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)  P2198  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)  


DESCRIPTION

HINT:
·

Although the DTC titles say heated oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.



The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is the planar type and is integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows through the heater to heat the sensor in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, thereby accelerating the sensor activation.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: The value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A225212E01
3.052,2.583 3.385,2.896 false 2.844,2.365 3.354,2.552 false 2.979,2.01 3.365,1.938 false 3,2.302 3.354,2.552 false 3.188,1.833 3.333,1.469 3.333,1.469 3.375,1.469 false 1.781,2.573 2.063,2.573 false 1.594,2.625 0.99,2.24 0.99,2.24 0.948,2.24 false 1.125,3.083 1.25,3.281 0.125,0.198 10 false A 2.021,3.083 2.146,3.281 0.125,0.198 10 false A 0.406,2.146 0.948,2.302 0.542,0.156 10 false Element 0.094,2.958 0.979,3.177 0.885,0.219 10 false Exhaust Gas 2.698,3.156 3.49,3.375 0.792,0.219 10 false A-A Section 3.417,2.469 4.625,2.688 1.208,0.219 10 false Platinum Electrode 2.094,2.479 2.656,2.698 0.563,0.219 10 false Cover 3.417,2.833 3.708,3.031 0.292,0.198 10 false Air 3.438,1.385 3.875,1.604 0.438,0.219 10 false Heater 3.406,1.771 4.594,2.156 1.188,0.385 10 false Solid Electrolyte (Zirconia Element) 5.156,3.094 6.865,3.313 1.708,0.219 10 false Rich - Air-fuel Ratio - Lean 5.771,0.417 7.125,0.635 1.354,0.219 10 false Ideal Air-Fuel Mixture 4.354,0.615 5.344,0.823 0.99,0.208 10 false Output Voltage 4.698,0.99 4.917,1.198 0.219,0.208 10 false (V) 4.677,2.552 4.896,2.708 0.219,0.156 10 false 2.4 4.677,2.396 4.896,2.552 0.219,0.156 10 false 2.6 4.677,2.229 4.896,2.385 0.219,0.156 10 false 2.8 4.677,2.073 4.896,2.229 0.219,0.156 10 false 3.0 4.677,1.906 4.896,2.063 0.219,0.156 10 false 3.2 4.677,1.75 4.896,1.906 0.219,0.156 10 false 3.4 4.677,1.583 4.896,1.74 0.219,0.156 10 false 3.6 4.677,1.427 4.896,1.583 0.219,0.156 10 false 3.8 4.677,1.26 4.896,1.417 0.219,0.156 10 false 4.0 5.094,2.823 5.292,2.99 0.198,0.167 10 false 12 5.323,2.823 5.521,2.99 0.198,0.167 10 false 13 5.552,2.823 5.75,2.99 0.198,0.167 10 false 14 5.792,2.823 5.99,2.99 0.198,0.167 10 false 15 6.021,2.823 6.219,2.99 0.198,0.167 10 false 16 6.25,2.823 6.448,2.99 0.198,0.167 10 false 17 6.479,2.823 6.677,2.99 0.198,0.167 10 false 18 6.708,2.823 6.906,2.99 0.198,0.167 10 false 19

DTC No. DTC Detection Condition Trouble Area
P2195
P2197
Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):

(a) The air fuel ratio sensor voltage is higher than 3.8 V.

(b) The heated oxygen sensor voltage is 0.21 V or higher.


·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Air fuel ratio sensor (bank 1, 2 sensor 1) heater

·

Air fuel ratio sensor heater circuits

·

No. 1 integration relay (A/F)

·

Air induction system circuits

·

Fuel pressure

·

Fuel injector assembly

·

ECM


While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 3.6 mA or higher for 3 seconds (2 trip detection logic).
·

Air fuel ratio sensor

·

ECM


P2196
P2198
Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):

(a) The air fuel ratio sensor voltage is below 2.8 V.

(b) The heated oxygen sensor voltage is below 0.59 V.


·

Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Air fuel ratio sensor (bank 1, 2 sensor 1) heater

·

Air fuel ratio sensor heater circuits

·

Air induction system

·

No. 1 integration relay (A/F)

·

Fuel pressure

·

Fuel injector assembly

·

ECM


While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is below than 1.4 mA for 3 seconds (2 trip detection logic).
·

Air fuel ratio sensor

·

ECM



HINT:
·

DTCs P2195 and P2196 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.

·

DTCs P2197 and P2198 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.

·

Bank 1 refers to the bank that includes cylinder No. 1.

·

Bank 2 refers to the bank that includes cylinder No. 2.

·

When any of these DTCs are stored, check the air fuel ratio sensor voltage output by entering the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS Voltage B1S1 or AFS Voltage B2S1.

·

The short-term fuel trim values can also be read using the GTS.

·

The ECM maintains the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM at a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the GTS.

·

If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.



WIRING DIAGRAM

for Automatic Transmission

A227126E17
3.229,1.75 4.604,2.094 1.375,0.344 10 false Air Fuel Ratio Sensor (for Bank 1 Sensor 1) 1.344,5.604 1.823,5.802 0.479,0.198 10 false Battery 1.188,4.417 1.552,4.583 0.365,0.167 10 false P/I-B 1.146,3.448 2.656,3.635 1.51,0.188 10 false No. 1 Integration Relay 0.802,3.24 0.938,3.417 0.135,0.177 10 false 1 1,3.25 1.208,3.406 0.208,0.156 10 false 1C 1.156,2.906 1.427,3.083 0.271,0.177 10 false EFI 1.635,2.365 1.885,2.521 0.25,0.156 10 false EFI 1,0.74 1.271,0.906 0.271,0.167 10 false A/F 1.635,1.198 1.906,1.365 0.271,0.167 10 false A/F 2.385,0.604 2.604,0.771 0.219,0.167 10 false 1B 2.385,0.885 2.604,1.052 0.219,0.167 10 false 1B 2.385,2.042 2.604,2.208 0.219,0.167 10 false 1B 2.385,2.635 2.604,2.802 0.219,0.167 10 false 1B 2.427,0.438 2.542,0.615 0.115,0.177 10 false 8 2.427,1.052 2.542,1.229 0.115,0.177 10 false 7 2.427,1.865 2.542,2.042 0.115,0.177 10 false 2 2.427,2.448 2.542,2.625 0.115,0.177 10 false 3 3.229,1.594 3.51,1.76 0.281,0.167 10 false C25 3.073,4.615 4.448,4.958 1.375,0.344 10 false Air Fuel Ratio Sensor (for Bank 2 Sensor 1) 3.073,4.458 3.354,4.625 0.281,0.167 10 false C26 3.396,0.49 3.51,0.667 0.115,0.177 10 false 2 4.427,0.49 4.542,0.667 0.115,0.177 10 false 1 3.396,1.281 3.51,1.458 0.115,0.177 10 false 4 4.427,1.281 4.542,1.458 0.115,0.177 10 false 3 3.573,0.49 3.802,0.656 0.229,0.167 10 false +B 3.979,0.49 4.406,0.646 0.427,0.156 10 false HA1A 3.573,1.25 3.917,1.417 0.344,0.167 10 false A1A- 4,1.26 4.406,1.417 0.406,0.156 10 false A1A+ 3.219,3.396 3.333,3.573 0.115,0.177 10 false 2 4.25,3.396 4.365,3.573 0.115,0.177 10 false 1 3.219,4.188 3.333,4.365 0.115,0.177 10 false 4 4.25,4.188 4.365,4.365 0.115,0.177 10 false 3 3.396,3.385 3.635,3.552 0.24,0.167 10 false +B 3.802,3.385 4.229,3.542 0.427,0.156 10 false HA2A 3.396,4.156 3.74,4.323 0.344,0.167 10 false A2A- 3.823,4.156 4.229,4.313 0.406,0.156 10 false A2A+ 5.24,0.427 5.438,0.604 0.198,0.177 10 false 17 5.198,0.604 5.49,0.781 0.292,0.177 10 false C37 5.521,0.51 5.927,0.677 0.406,0.167 10 false HA1A 5.281,1.208 5.438,1.385 0.156,0.177 10 false 7 5.188,1.385 5.479,1.563 0.292,0.177 10 false C35 5.521,1.292 5.927,1.458 0.406,0.167 10 false A1A+ 5.281,2.26 5.438,2.438 0.156,0.177 10 false 8 5.188,2.448 5.479,2.625 0.292,0.177 10 false C35 5.229,2.885 5.448,3.063 0.219,0.177 10 false 36 5.177,3.073 5.469,3.25 0.292,0.177 10 false G56 5.521,2.354 5.927,2.521 0.406,0.167 10 false A1A- 5.281,4.094 5.438,4.271 0.156,0.177 10 false 1 5.188,4.271 5.479,4.448 0.292,0.177 10 false C35 5.521,4.188 5.927,4.354 0.406,0.167 10 false A2A+ 5.281,5.26 5.438,5.438 0.156,0.177 10 false 2 5.188,5.438 5.479,5.615 0.292,0.177 10 false C35 5.521,5.344 5.927,5.51 0.406,0.167 10 false A2A- 5.24,3.313 5.438,3.49 0.198,0.177 10 false 12 5.188,3.5 5.479,3.677 0.292,0.177 10 false C37 5.521,3.396 5.927,3.563 0.406,0.167 10 false HA2A 5.958,5.99 6.313,6.156 0.354,0.167 10 false ECM 5.521,2.979 5.948,3.146 0.427,0.167 10 false MREL 0.479,6.469 1.417,6.625 0.938,0.156 10 false *: Shielded 4.75,3.948 4.865,4.115 0.115,0.167 10 false * 4.844,1.042 4.958,1.208 0.115,0.167 10 false *

for Manual Transmission

A227126E09
3.225,1.748 4.603,2.089 1.378,0.341 10 Air Fuel Ratio Sensor (for Bank 1 Sensor 1) 1.345,5.603 1.825,5.796 0.480,0.193 10 Battery 1.19,4.421 1.559,4.586 0.369,0.165 10 P/I-B 1.144,3.446 2.652,3.629 1.508,0.184 10 No. 1 Integration Relay 0.799,3.237 0.936,3.412 0.137,0.174 10 1 1,3.25 1.211,3.410 0.211,0.161 10 1C 1.158,2.904 1.435,3.078 0.276,0.174 10 EFI 1.638,2.362 1.891,2.521 0.253,0.158 10 EFI 0.995,0.737 1.262,0.902 0.267,0.165 10 A/F 1.639,1.195 1.906,1.360 0.267,0.165 10 A/F 2.382,0.601 2.603,0.766 0.221,0.165 10 1B 2.382,0.877 2.603,1.042 0.221,0.165 10 1B 2.382,2.037 2.603,2.202 0.221,0.165 10 1B 2.382,2.633 2.603,2.798 0.221,0.165 10 1B 2.429,0.438 2.547,0.613 0.119,0.174 10 8 2.429,1.053 2.547,1.228 0.119,0.174 10 7 2.429,1.866 2.547,2.040 0.119,0.174 10 2 2.429,2.451 2.547,2.625 0.119,0.174 10 3 3.225,1.592 3.511,1.757 0.286,0.165 10 C25 3.073,4.619 4.451,4.961 1.378,0.341 10 Air Fuel Ratio Sensor (for Bank 2 Sensor 1) 3.073,4.463 3.359,4.628 0.286,0.165 10 C26 3.4,0.494 3.519,0.669 0.119,0.174 10 2 4.429,0.494 4.548,0.669 0.119,0.174 10 1 3.4,1.284 3.519,1.458 0.119,0.174 10 4 4.429,1.284 4.548,1.458 0.119,0.174 10 3 3.577,0.485 3.807,0.650 0.230,0.165 10 +B 3.979,0.485 4.404,0.641 0.424,0.156 10 HA1A 3.577,1.255 3.919,1.421 0.341,0.165 10 A1A- 3.998,1.256 4.404,1.411 0.406,0.156 10 A1A+ 3.223,3.399 3.341,3.574 0.119,0.174 10 2 4.251,3.399 4.370,3.574 0.119,0.174 10 1 3.223,4.188 3.341,4.363 0.119,0.174 10 4 4.251,4.188 4.370,4.363 0.119,0.174 10 3 3.4,3.39 3.640,3.555 0.240,0.165 10 +B 3.802,3.39 4.226,3.546 0.424,0.156 10 HA2A 3.4,4.16 3.741,4.326 0.341,0.165 10 A2A- 3.82,4.16 4.226,4.316 0.406,0.156 10 A2A+ 5.241,0.424 5.443,0.599 0.202,0.174 10 17 5.208,0.607 5.503,0.781 0.295,0.174 10 C37 5.516,0.513 5.922,0.678 0.406,0.165 10 HA1A 5.283,1.205 5.443,1.379 0.161,0.174 10 1 5.208,1.388 5.503,1.562 0.295,0.174 10 C36 5.516,1.294 5.922,1.459 0.406,0.165 10 A1A+ 5.283,2.26 5.443,2.435 0.161,0.174 10 2 5.208,2.443 5.503,2.618 0.295,0.174 10 C36 5.283,2.886 5.443,3.060 0.161,0.174 10 9 5.208,3.069 5.503,3.243 0.295,0.174 10 G55 5.516,2.349 5.922,2.514 0.406,0.165 10 A1A- 5.283,4.095 5.443,4.269 0.161,0.174 10 7 5.208,4.278 5.503,4.452 0.295,0.174 10 C36 5.516,4.184 5.922,4.349 0.406,0.165 10 A2A+ 5.283,5.259 5.443,5.433 0.161,0.174 10 8 5.208,5.441 5.503,5.616 0.295,0.174 10 C36 5.516,5.347 5.922,5.512 0.406,0.165 10 A2A- 5.241,3.31 5.443,3.485 0.202,0.174 10 19 5.208,3.493 5.503,3.668 0.295,0.174 10 C37 5.516,3.399 5.922,3.564 0.406,0.165 10 HA2A 5.959,5.986 6.314,6.152 0.355,0.165 10 ECM 5.52,2.979 5.945,3.144 0.424,0.165 10 MREL 0.477,6.472 1.415,6.628 0.938,0.156 10 *: Shielded 4.752,3.944 4.870,4.109 0.119,0.165 10 * 4.845,1.043 4.964,1.208 0.119,0.165 10 *

CONFIRMATION DRIVING PATTERN

CAUTION:

Strictly observe posted speed limits, traffic laws and road conditions when performing these driving patterns.


HINT:

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" step of the following diagnostic troubleshooting procedure.


A371142E03
2.667,1.51 3,0.958 3,0.958 2.865,0.958 false 4.917,1.729 4.542,0.698 false 5.021,1.51 4.531,1.51 false 5.49,1.833 5.729,0.74 false 5.365,2.281 6.167,2.281 false 3.833,3.344 4.313,3.51 false 0.094,0.063 2.021,0.292 1.927,0.229 10 false Confirmation Driving Pattern: 0.104,0.365 2.833,0.552 2.729,0.188 10 false ECT: 75°C (167°F) or more 0.125,0.885 1.115,1.083 0.99,0.198 10 false Vehicle Speed 1.167,0.865 2.802,1.208 1.635,0.344 10 false Between 60 and 120 km/h (38 and 75 mph) 1.521,2.156 1.771,2.365 0.25,0.208 10 false (e) 2.823,1.281 3.073,1.49 0.25,0.208 10 false (g) 0.698,2.271 1.125,2.49 0.427,0.219 10 false Idling 1.24,2.833 2.083,3.073 0.844,0.24 10 false Warming up 2.469,2.823 3.188,3.167 0.719,0.344 10 false 10 minutes or more 3.385,0.594 4.542,0.969 1.156,0.375 10 false Accelerator Pedal Depressed 3.375,1.417 4.5,1.792 1.125,0.375 10 false 64 km/h (40 mph) or more 3.708,2.146 3.958,2.354 0.25,0.208 10 false (h) 4.885,1.292 5.135,1.5 0.25,0.208 10 false (i) 5.26,1.292 5.51,1.5 0.25,0.208 10 false (j) 5.594,1.75 5.844,1.958 0.25,0.208 10 true (k) 5.792,0.563 7.042,0.958 1.25,0.396 10 false Accelerator Pedal Released (Fuel-cut) 6.24,2 6.823,2.385 0.583,0.385 10 true 10 km/h (6 mph) 6.083,2.531 6.479,2.74 0.396,0.208 10 false Time 4.594,2.792 5.354,3.146 0.76,0.354 10 false 10 seconds or more 5.427,2.771 6.115,3.125 0.688,0.354 10 true 4 seconds or more 4.385,3.406 5.708,3.594 1.323,0.188 10 false Refer to figure below 4.635,0.688 5.688,0.875 1.052,0.188 10 false At least 3 times

A371143E03
3.354,2.615 2.563,1.021 false 3.604,2.615 4.073,0.958 false 0.073,0.063 2.594,0.292 2.521,0.229 10 false Driving Pattern Detail for (h) through (k): 0.229,0.531 1.833,0.729 1.604,0.198 10 false Reference Engine Speed 0.792,1.833 1.427,2.042 0.635,0.208 10 false 2500 rpm 0.802,2.208 1.458,2.417 0.656,0.208 10 false 1000 rpm 1.052,2.385 1.469,2.594 0.417,0.208 10 false Idling 2.083,2.979 2.5,3.188 0.417,0.208 10 false Idling 2.125,2.51 2.385,2.708 0.26,0.198 10 false [C] 2.771,1.229 3.031,1.427 0.26,0.198 10 false (i) 2.156,0.833 2.573,1.042 0.417,0.208 10 false Delay 3.271,1.208 3.531,1.406 0.26,0.198 10 false (j) 4.146,0.792 5.427,0.99 1.281,0.198 10 false Detection Period t1 3.458,1.594 3.719,1.792 0.26,0.198 10 false (k) 3.156,3.094 3.844,3.458 0.688,0.365 10 false 4 seconds or more 4.385,3.094 5.073,3.458 0.688,0.365 10 false 4 seconds or more 5.615,3.083 6.302,3.448 0.688,0.365 10 false 4 seconds or more 4.771,2.396 4.969,2.594 0.198,0.198 10 false t2 6.01,2.385 6.208,2.583 0.198,0.198 10 false t3 6.51,2.771 6.927,2.979 0.417,0.208 10 false Time 2.969,0.323 7.104,0.51 4.135,0.188 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more

(a) Connect the GTS to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the GTS on.

(e) Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher.

(f) Enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / All Data / Idle Fuel Cut.

(g) Drive the vehicle at between 60 km/h (38 mph) and 120 km/h (75 mph) for at least 10 minutes.

(h) Shift the transmission to 2nd gear.

(i) Drive the vehicle at the proper vehicle speed to perform fuel-cut operation (refer to the following hint).

HINT:

Fuel-cut is performed when the following conditions are met:

·

The accelerator pedal is fully released.

·

The engine speed is 2500 rpm or more (fuel injection returns at 2000 rpm).



(j) Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds.

(k) Soon after performing step (j) above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control.

(l) Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

(m) Repeat steps (h) through (k) above at least 3 times in one driving cycle.

HINT:

Completion of O2S (A/F) Monitor is required to change the value in the Data List.



CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for air fuel ratio sensor function provided in the Active Test. The Control the Injection Volume for air fuel ratio sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for air fuel ratio sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

On the GTS, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume.)

6.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for air fuel ratio sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E50
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.469,1.604 1.917,1.792 0.448,0.188 8 false +12.5% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.135 6.885,6.563 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leakage from exhaust system (air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.417,3.677 1.865,3.865 0.448,0.188 8 false +12.5% 4.01,1.594 4.458,1.781 0.448,0.188 8 false +12.5% 4,3.667 4.448,3.854 0.448,0.188 8 false +12.5% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.406,5.75 1.854,5.938 0.448,0.188 8 false +12.5% 1.375,7.771 1.823,7.958 0.448,0.188 8 false +12.5% 4.031,7.792 4.479,7.979 0.448,0.188 8 false +12.5% 4.073,5.729 4.521,5.917 0.448,0.188 8 false +12.5% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for air fuel ratio sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P2195, P2196, P2197 or P2198 A
P2195, P2196, P2197 or P2198 and other DTCs B

HINT:

If any DTCs other than P2195, P2196, P2197 or P2198 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)

B

2.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1 and AFS Current B2S1.


f.

Check the test value of the air fuel ratio sensor output current during fuel-cut.

Result
Result Proceed to
Within normal range (1.4 mA or higher, and below 3.6 mA) A
Outside normal range (Below 1.4 mA, or 3.6 mA or higher) B



A

3.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

B

20.REPLACE AIR FUEL RATIO SENSOR
3.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Snapshot / AFS Voltage B1S1 or AFS Voltage B2S1 and Engine Speed.


f.

Check the air fuel ratio sensor voltage three times, once in each of the following conditions:

i.

Engine idling (check for at least 30 seconds)


ii.

Engine running at an engine speed of approximately 2500 rpm (without any sudden changes in engine speed)


iii.

Engine speed raised to 4000 rpm and then accelerator pedal quickly released so that the throttle valve is fully closed

Standard:
Condition Air Fuel Ratio Sensor Voltage Variation Reference
(1) and (2) Changes at approximately 3.3 V Between 3.1 V and 3.5 V
(3) Increases to 3.8 V or higher This occurs during engine deceleration
(during fuel-cut)


HINT:

For more information, see the diagrams below.


A373188E03
2.646,1.604 2.833,0.833 false 1.698,1.833 1.479,1.115 false 1.115,1.958 1.198,1.708 false 1.74,2.563 1.333,3.063 1.333,3.063 1.458,2.521 false 2.833,3.104 2.719,2.375 false 3.052,1.958 3.115,1.729 false 2.656,2.948 2.729,2.802 false 5.313,1.833 5.5,1.063 false 6.229,1.594 6.417,0.823 false 4.635,1.969 4.719,1.719 false 6.604,1.969 6.667,1.74 false 5,2.99 5.146,2.552 false 0.115,0.083 1.521,0.313 1.406,0.229 10 false Normal Condition: 3.667,0.073 5.427,0.281 1.76,0.208 10 false Malfunction Condition: 1.688,0.438 3.521,0.625 1.833,0.188 10 false (3) Approximately 4000 rpm 0.094,0.781 1.927,0.969 1.833,0.188 10 false (2) Approximately 2500 rpm 0.958,1.417 1.563,1.604 0.604,0.188 10 false (1) Idling 2.74,1.427 3.344,1.615 0.604,0.188 10 false (1) Idling 0.01,1.875 0.948,2.052 0.938,0.177 10 false Engine Speed 0.135,2.406 0.906,2.75 0.771,0.344 10 false A/F Sensor Voltage 3.604,1.875 4.542,2.052 0.938,0.177 10 false Engine Speed 0.219,3.115 2.042,3.49 1.823,0.375 10 false "Condition (A), (B)": Remains at approximately 3.3 V 2.063,2.875 2.667,3.063 0.604,0.188 10 false Fuel-cut 2.438,3.125 3.448,3.49 1.01,0.365 10 false "Condition (C)": 3.8 V or higher 3.688,2.365 4.458,2.708 0.771,0.344 10 false A/F Sensor Voltage 4.313,0.708 6.104,0.896 1.792,0.188 10 false (2) Approximately 2500 rpm 5.375,0.344 7.135,0.542 1.76,0.198 10 false (3) Approximately 4000 rpm 4.563,1.406 5.167,1.594 0.604,0.188 10 false (1) Idling 6.323,1.396 6.927,1.583 0.604,0.188 10 false (1) Idling 6.125,2.844 6.729,3.031 0.604,0.188 10 false Fuel-cut 3.625,2.99 6.115,3.375 2.49,0.385 10 false When A/F sensor circuit malfunctioning, voltage output does not change



HINT:
·

If the output voltage of the air fuel ratio sensor remains at approximately 3.3 V (see "Malfunctioning" diagram) under any conditions, including those above, the air fuel ratio sensor may have an open circuit. (This will also happen if the air fuel ratio sensor heater has an open circuit.)

·

If the output voltage of the air fuel ratio sensor remains at either approximately 3.8 V or higher, or 2.8 V or less (see "Malfunctioning" diagram) under any conditions, including those above, the air fuel ratio sensor may have a short circuit.

·

The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the air fuel ratio sensor output voltage.

·

The ECM must establish a closed throttle valve position learned value to perform fuel cut. If the battery cable has been disconnected and reconnected, the vehicle must be driven over 16 km/h (10 mph) to allow the ECM to learn the closed throttle valve position.

·

When the vehicle is driven:

The output voltage of the air fuel ratio sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The air fuel ratio sensor is functioning normally.

·

The air fuel ratio sensor is a current output element. Therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the air fuel ratio sensor or ECM will show a constant voltage.




OK

4.PERFORM CONFIRMATION DRIVING PATTERN

NG

10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
4.PERFORM CONFIRMATION DRIVING PATTERN

NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


d.

Read the DTCs.

Result
Result Proceed to
P2195, P2196, P2197 or P2198 A
No output B



A

6.REPLACE AIR FUEL RATIO SENSOR

B

9.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
6.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

7.PERFORM CONFIRMATION DRIVING PATTERN
7.PERFORM CONFIRMATION DRIVING PATTERN

NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


d.

Read DTCs.

Result
Result Proceed to
No output A
P2195, P2196, P2197 or P2198 B



A

9.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN

9.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO

10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

11.INSPECT NO. 1 INTEGRATION RELAY (A/F)

NG

11.INSPECT NO. 1 INTEGRATION RELAY (A/F)
a.

Inspect the No. 1 integration relay (A/F) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

12.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (A/F)

12.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C37-17 (HA1A) Always Below 1 Ω
C26-1 (HA2A) - C37-12 (HA2A) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C37-17 (HA1A) Always Below 1 Ω
C26-1 (HA2A) - C37-19 (HA2A) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) or C37-17 (HA1A) - Body ground Always 10 kΩ or higher
C26-1 (HA2A) or C37-12 (HA2A) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C25-1 (HA1A) or C37-17 (HA1A) - Body ground Always 10 kΩ or higher
C26-1 (HA2A) or C37-19 (HA2A) - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reconnect the ECM connector.



OK

13.CHECK AIR INDUCTION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage.

OK:

No leakage in air induction system.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

14.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

14.CHECK FUEL PRESSURE

OK

15.INSPECT FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE FUEL SYSTEM

15.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the injector injection (whether fuel volume is large or small, and whether injection pattern is poor) (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

16.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

16.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

17.PERFORM CONFIRMATION DRIVING PATTERN
17.PERFORM CONFIRMATION DRIVING PATTERN

NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


d.

Read DTCs.

Result
Result Proceed to
No output A
P2195, P2196, P2197 or P2198 B



A

19.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN

19.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO

20.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

21.PERFORM CONFIRMATION DRIVING PATTERN
21.PERFORM CONFIRMATION DRIVING PATTERN

NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
22.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


d.

Read DTCs.

Result
Display (DTC Output) Proceed to
No output A
P2195, P2196, P2197 or P2198 (air fuel ratio sensor pending DTCs) B



A

END

B