Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  P0156  Oxygen Sensor Circuit (Bank 2 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  P0158  Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)  


DESCRIPTION

HINT:

Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.


A three-way catalyst converter is used in order to convert the carbon monoxide, hydrocarbons and nitrogen oxide into less harmful substances. To allow the three-way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the three-way catalytic converter, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-three way catalytic converter air fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-three way catalytic converter air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the three-way catalytic converter is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A208686E01
2.634,2.044 3.123,2.044 false 2.549,1.815 3.123,1.815 false 2.656,1.582 3.123,1.582 false 3.325,0.559 3.980,0.775 0.655,0.216 10 Housing 3.325,0.898 4.576,1.253 1.251,0.355 10 Solid Electrolyte (Zirconia Element) 3.157,1.496 4.408,1.682 1.251,0.186 10 Platinum Electrode 3.157,1.748 3.714,1.934 0.557,0.186 10 Heater 3.157,1.982 4.390,2.168 1.233,0.186 10 Coating (Ceramic) 1.044,2.219 1.24,2.219 false 1.294,2.157 1.748,2.343 0.455,0.186 10 Cover 1.777,2.472 2.621,2.658 0.844,0.186 10 Exhaust Gas 1.676,0 2.529,0.186 0.853,0.186 10 Atmosphere 3.955,0.21 4.956,0.396 1.001,0.186 10 Output Voltage 5.17,0.229 6.634,0.415 1.464,0.186 10 Ideal Air Fuel Mixture 4.723,2.246 6.818,2.392 2.096,0.146 10 Richer - Air Fuel Ratio - Leaner 2.689,1.451 3.23,0.965 3.23,0.965 3.305,0.965 false 3.072,0.62 3.291,0.62 false

DTC No. DTC Detection Condition Trouble Area
P0136
P0156
·

Abnormal voltage output:

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

The heated oxygen sensor voltage does not decrease to below 0.21 V.

(b)

The heated oxygen sensor voltage does not increase to higher than 0.59 V.



·

Open or short in heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Heated oxygen sensor heater (bank 1, 2 sensor 2)

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

Gas leak from exhaust system


P0137
P0157
·

Low voltage (open):

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

The heated oxygen sensor voltage output is below 0.21 V.

(b)

The target air fuel ratio is rich.



·

Open in heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Heated oxygen sensor heater (bank 1, 2 sensor 2)

·

Gas leak from exhaust system


P0138
P0158
·

High voltage (short):

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a)

The heated oxygen sensor voltage output is 0.59 V or higher.

(b)

The target air fuel ratio is lean.



·

Short in heated oxygen sensor (bank 1, 2 sensor 2) circuit

·

Heated oxygen sensor (bank 1, 2 sensor 2)

·

Air fuel ratio sensor (bank 1, 2 sensor 1)

·

ECM



WIRING DIAGRAM

for Automatic Transmission

A358814E01
0.553,5.309 1.042,5.493 0.489,0.184 10 Battery 0.422,3.338 0.781,3.504 0.360,0.165 10 P/I-B 0.521,0.408 0.649,0.573 0.128,0.165 10 1 0.478,0.602 0.708,0.767 0.230,0.165 10 1C 2.333,0.408 2.461,0.573 0.128,0.165 10 4 0.841,1.458 0.969,1.623 0.128,0.165 10 3 2.29,0.602 2.520,0.767 0.230,0.165 10 1B 2.333,0.846 2.461,1.011 0.128,0.165 10 2 2.29,1.039 2.520,1.204 0.230,0.165 10 1B 1.046,1.465 1.276,1.630 0.230,0.165 10 1B 0.964,0.751 1.240,0.916 0.276,0.165 10 EFI 1.696,1.368 1.963,1.533 0.267,0.165 10 EFI 1.174,1.695 2.672,1.897 1.498,0.202 10 No. 1 Integration Relay 2.738,0.751 3.385,0.935 0.647,0.184 10 EFI No. 2 3.829,0.499 3.948,0.664 0.119,0.165 10 2 3.829,1.274 3.948,1.439 0.119,0.165 10 4 4.844,0.499 4.963,0.664 0.119,0.165 10 1 4.844,1.274 4.963,1.439 0.119,0.165 10 3 4.018,0.494 4.248,0.659 0.230,0.165 10 +B 4.008,1.274 4.229,1.449 0.221,0.174 10 E2 4.419,0.48 4.798,0.636 0.378,0.156 10 HT1B 4.382,1.209 4.797,1.374 0.415,0.165 10 OX1B 3.586,3.149 3.705,3.314 0.119,0.165 10 2 3.586,3.924 3.705,4.089 0.119,0.165 10 4 4.602,3.149 4.720,3.314 0.119,0.165 10 1 4.602,3.924 4.720,4.089 0.119,0.165 10 3 3.775,3.144 4.005,3.309 0.230,0.165 10 +B 3.766,3.924 3.986,4.099 0.221,0.174 10 E2 4.177,3.13 4.555,3.286 0.378,0.156 10 HT2B 4.139,3.859 4.554,4.024 0.415,0.165 10 OX2B 3.654,1.573 3.948,1.738 0.295,0.165 10 C27 3.654,1.723 5.134,2.073 1.480,0.350 10 Heated Oxygen Sensor (for Bank 1 Sensor 2) 3.327,4.193 3.714,4.395 0.387,0.202 10 C145 3.336,4.366 4.816,4.716 1.480,0.350 10 Heated Oxygen Sensor (for Bank 2 Sensor 2) 6.297,5.972 6.647,6.156 0.350,0.184 10 ECM 5.68,0.411 5.873,0.585 0.193,0.174 10 18 5.989,0.506 6.395,0.671 0.406,0.165 10 HT1B 5.648,0.603 5.962,0.777 0.313,0.174 10 C37 5.727,1.196 5.874,1.370 0.147,0.174 10 9 5.989,1.377 6.395,1.542 0.406,0.165 10 OX1B 5.648,1.387 5.962,1.562 0.313,0.174 10 C35 5.697,2.466 5.913,2.640 0.216,0.174 10 10 5.989,2.647 6.395,2.812 0.406,0.165 10 EX1B 5.648,2.657 5.962,2.832 0.313,0.174 10 C35 5.68,3.054 5.873,3.229 0.193,0.174 10 13 5.989,3.149 6.395,3.314 0.406,0.165 10 HT2B 5.648,3.246 5.962,3.420 0.313,0.174 10 C37 5.727,3.83 5.874,4.004 0.147,0.174 10 3 5.989,4.011 6.395,4.176 0.406,0.165 10 OX2B 5.648,4.021 5.962,4.195 0.313,0.174 10 C35 5.736,5.006 5.874,5.181 0.137,0.174 10 4 5.989,5.188 6.395,5.353 0.406,0.165 10 EX2B 5.648,5.198 5.962,5.372 0.313,0.174 10 C35 5.703,5.455 5.919,5.629 0.216,0.174 10 36 5.989,5.544 6.395,5.709 0.406,0.165 10 MREL 5.643,5.646 5.956,5.821 0.313,0.174 10 G56 4.541,2.742 5.169,2.898 0.628,0.156 10 Shielded 4.453,5.293 5.081,5.449 0.628,0.156 10 Shielded

for Manual Transmission

A227125E09
0.563,5.311 1.052,5.495 0.489,0.184 10 Battery 0.432,3.34 0.792,3.505 0.360,0.165 10 P/I-B 0.531,0.41 0.659,0.575 0.128,0.165 10 1 0.488,0.604 0.718,0.769 0.230,0.165 10 1C 2.343,0.41 2.471,0.575 0.128,0.165 10 4 0.851,1.46 0.979,1.625 0.128,0.165 10 3 2.3,0.604 2.530,0.769 0.230,0.165 10 1B 2.343,0.847 2.471,1.013 0.128,0.165 10 2 2.3,1.041 2.530,1.206 0.230,0.165 10 1B 1.056,1.467 1.286,1.632 0.230,0.165 10 1B 0.974,0.753 1.250,0.918 0.276,0.165 10 EFI 1.706,1.369 1.973,1.535 0.267,0.165 10 EFI 1.184,1.696 2.682,1.899 1.498,0.202 10 No. 1 Integration Relay 2.748,0.753 3.395,0.937 0.647,0.184 10 EFI No. 2 3.839,0.501 3.958,0.666 0.119,0.165 10 2 3.839,1.276 3.958,1.441 0.119,0.165 10 4 4.855,0.501 4.973,0.666 0.119,0.165 10 1 4.855,1.276 4.973,1.441 0.119,0.165 10 3 4.028,0.495 4.258,0.661 0.230,0.165 10 +B 4.019,1.276 4.239,1.450 0.221,0.174 10 E2 4.43,0.482 4.808,0.638 0.378,0.156 10 HT1B 4.392,1.211 4.807,1.376 0.415,0.165 10 OX1B 3.596,3.151 3.715,3.316 0.119,0.165 10 2 3.596,3.926 3.715,4.091 0.119,0.165 10 4 4.612,3.151 4.731,3.316 0.119,0.165 10 1 4.612,3.926 4.731,4.091 0.119,0.165 10 3 3.785,3.145 4.015,3.311 0.230,0.165 10 +B 3.776,3.926 3.997,4.101 0.221,0.174 10 E2 4.187,3.132 4.565,3.288 0.378,0.156 10 HT2B 4.149,3.861 4.565,4.026 0.415,0.165 10 OX2B 3.664,1.575 3.959,1.740 0.295,0.165 10 C27 3.664,1.724 5.144,2.075 1.480,0.350 10 Heated Oxygen Sensor (for Bank 1 Sensor 2) 3.43,4.209 3.725,4.374 0.295,0.165 10 C28 3.43,4.358 4.910,4.709 1.480,0.350 10 Heated Oxygen Sensor (for Bank 2 Sensor 2) 6.307,5.974 6.657,6.158 0.350,0.184 10 ECM 5.691,0.413 5.884,0.587 0.193,0.174 10 12 5.999,0.507 6.405,0.672 0.406,0.165 10 HT1B 5.659,0.604 5.972,0.779 0.313,0.174 10 C37 5.737,1.197 5.884,1.372 0.147,0.174 10 2 5.999,1.379 6.405,1.544 0.406,0.165 10 OX1B 5.659,1.389 5.972,1.563 0.313,0.174 10 C34 5.747,2.468 5.884,2.642 0.137,0.174 10 1 5.999,2.649 6.405,2.814 0.406,0.165 10 EX1B 5.659,2.659 5.972,2.834 0.313,0.174 10 C34 5.691,3.056 5.884,3.230 0.193,0.174 10 13 5.999,3.151 6.405,3.316 0.406,0.165 10 HT2B 5.659,3.248 5.972,3.422 0.313,0.174 10 C37 5.737,3.831 5.884,4.006 0.147,0.174 10 4 5.999,4.013 6.405,4.178 0.406,0.165 10 OX2B 5.659,4.023 5.972,4.197 0.313,0.174 10 C34 5.747,5.008 5.884,5.183 0.137,0.174 10 3 5.999,5.19 6.405,5.355 0.406,0.165 10 EX2B 5.659,5.2 5.972,5.374 0.313,0.174 10 C34 5.747,5.457 5.884,5.631 0.137,0.174 10 9 5.999,5.546 6.405,5.711 0.406,0.165 10 MREL 5.659,5.648 5.972,5.823 0.313,0.174 10 G55 4.981,1.02 5.609,1.176 0.628,0.156 10 Shielded 4.79,3.656 5.418,3.812 0.628,0.156 10 Shielded

CONFIRMATION DRIVING PATTERN

A200170E05
2.707,2.371 2.918,2.559 0.211,0.188 10 [B] 4.133,0.731 4.349,0.919 0.216,0.188 10 [C] 5.074,3.102 5.297,3.295 0.223,0.193 10 [D] 1.04,0.498 2.441,0.681 1.401,0.184 10 120 km/h 1.092,1.374 2.359,1.558 1.267,0.184 10 60 km/h 1.274,2.224 1.673,2.388 0.399,0.165 10 Idling 0.243,2.459 1.647,2.618 1.403,0.160 10 Engine Switch on (IG) 2.426,3.135 3.235,3.319 0.809,0.184 10 Warming up 3.606,3.199 4.845,3.337 1.239,0.137 10 10 minutes or more 2.074,2.569 2.285,2.758 0.211,0.188 10 [A]

1.

Connect the GTS to the DLC3.

2.

Clear the DTCs.

3.

Turn the engine switch off.

4.

Turn the engine switch on (IG) and turn the GTS on (Step "A").

5.

Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more (Step "B").

6.

With the transmission in 4th gear or more, drive the vehicle at 60 to 120 km/h (37 to 75 mph) for 10 minutes or more (Step "C").

7.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

8.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

9.

Check the DTC judgment result (Step "D").

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, perform the driving pattern adding the vehicle speed and using the second gear to decelerate the vehicle.


CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for air fuel ratio sensor function provided in the Active Test. The Control the Injection Volume for air fuel ratio sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for air fuel ratio sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for air fuel ratio sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E50
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.469,1.604 1.917,1.792 0.448,0.188 8 false +12.5% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.135 6.885,6.563 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leakage from exhaust system (air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.417,3.677 1.865,3.865 0.448,0.188 8 false +12.5% 4.01,1.594 4.458,1.781 0.448,0.188 8 false +12.5% 4,3.667 4.448,3.854 0.448,0.188 8 false +12.5% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.406,5.75 1.854,5.938 0.448,0.188 8 false +12.5% 1.375,7.771 1.823,7.958 0.448,0.188 8 false +12.5% 4.031,7.792 4.479,7.979 0.448,0.188 8 false +12.5% 4.073,5.729 4.521,5.917 0.448,0.188 8 false +12.5% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for air fuel ratio sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio sensor and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0138 or P0158 A
P0137 or P0157 B
P0136 or P0156 C



A

2.READ VALUE USING GTS (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

9.CHECK FOR EXHAUST GAS LEAK

C

7.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
2.READ VALUE USING GTS (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1S2 or O2S B2S2.


e.

Allow the engine to idle.


f.

Read the heated oxygen sensor output voltage while idling.

Result
Result Proceed to
Higher than 1.0 V A
Below 1.0 V B



A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.
A224879E10
0.885,0.625 1.427,1.052 false 1.938,1 2.438,0.604 false 1.469,1.521 0.844,1.875 false 1.938,1.521 2.417,1.875 false 0.781,2.948 1.323,3.375 false 2.021,3.313 2.51,2.917 false 1.375,3.844 0.74,4.188 false 2.021,3.833 2.49,4.188 false 0.083,0.031 0.292,0.188 0.208,0.156 10 false *a 0.083,2.313 0.292,2.469 0.208,0.156 10 false *b 2.49,0.51 2.927,0.667 0.438,0.156 10 false HT1B 0.583,0.51 0.802,0.688 0.219,0.177 10 false +B 0.583,1.802 0.813,1.958 0.229,0.156 10 false E2 2.49,1.802 2.917,1.979 0.427,0.177 10 false OX1B 2.563,2.823 3.115,3 0.552,0.177 10 false HT2B*B 0.479,2.823 0.698,3 0.219,0.177 10 false +B 0.479,4.115 0.708,4.271 0.229,0.156 10 false E2 2.563,4.115 3.125,4.323 0.563,0.208 10 false OX2B*B 0.083,0.219 0.292,0.375 0.208,0.156 10 false *c 2.49,0.688 3.083,0.875 0.594,0.188 10 false HT2B*A 2.49,1.969 3.083,2.156 0.594,0.188 10 false OX2B*A

Disconnect the heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Bank 1 Sensor 2):
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) 20°C (68°F) 10 kΩ or higher
2 (+B) - 3 (OX1B) Always 10 kΩ or higher


Standard Resistance (Bank 2 Sensor 2):
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) 20°C (68°F) 10 kΩ or higher
2 (+B) - 3 (OX2B) Always 10 kΩ or higher


Text in Illustration
*A for Automatic Transmission
*B for Manual Transmission
*a Component without harness connected
(to Heated Oxygen Sensor Bank 1)
*b Component without harness connected
(to Heated Oxygen Sensor Bank 2)
*c Component without harness connected
(to Heated Oxygen Sensor Bank 2)


c.

Reconnect the heated oxygen sensor connector.



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transmission
Tester Connection Condition Specified Condition
C37-18 (HT1B) - C35-9 (OX1B) Always 10 kΩ or higher
C37-13 (HT2B) - C35-3 (OX2B) Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C37-12 (HT1B) - C34-2 (OX1B) Always 10 kΩ or higher
C37-13 (HT2B) - C34-4 (OX2B) Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

5.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.


f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations within this range.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the GTS.



Result
GTS Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio sensor)
Alternates between higher than and below 3.3 V OK
Remains at higher than 3.3 V NG
Remains at below 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either below or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E04
5.875,2.458 6.188,1.479 false 5.552,2.271 6.188,1.479 false 5.719,1.667 6.188,1.479 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.396,1.865 4.094,1.698 false 3.531,2.729 3.208,2.927 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 3.3 V 2.656,0.26 3.083,0.458 0.427,0.198 10 +12% 4.125,1.125 4.51,1.323 0.385,0.198 10 -12% 1.656,2.854 1.906,3.052 0.25,0.198 10 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 Malfunction 5.854,2.615 6.583,2.792 0.729,0.177 10 Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 Injection Volume 3.583,2.635 5.583,2.781 2,0.146 10 Heated Oxygen Sensor Output 6.229,1.219 7.156,1.906 0.927,0.688 10 Air Fuel Ratio Sensor Output 4.406,1.813 4.896,1.979 0.49,0.167 10 Normal



OK

6.CHECK AIR FUEL RATIO SENSOR

NG

15.REPLACE AIR FUEL RATIO SENSOR
6.CHECK AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will be below 3 mA in this test.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Clear.


e.

Clear DTCs.


f.

Drive the vehicle according to the driving pattern listed below:

i.

Warm up the engine.


ii.

Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.


iii.

Stop the vehicle.


iv.

Accelerate the vehicle to 60 km/h (40 mph) or more and then decelerate for 5 seconds or more. Repeat this process at least 3 times.

A152792E20
1.357,2.513 2.638,2.697 1.281,0.184 10 10 minutes or more 2.973,2.513 4.186,2.697 1.213,0.184 10 5 seconds or more 4.271,2.513 5.468,2.697 1.197,0.184 10 5 seconds or more 5.56,2.513 6.739,2.697 1.179,0.184 10 5 seconds or more 0.152,0.078 1.451,0.293 1.299,0.215 12 Driving Pattern: 0.348,1.224 1.006,1.602 0.658,0.378 10 60 km/h (40 mph) 0.348,2.055 0.884,2.415 0.536,0.360 10 0 km/h (0 mph)



g.

Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Current B1S1 and AFS Current B2S1.


h.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard current:

Below 3.0 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.




Result
Result Proceed to
Outside standard range A
Within standard range B


OK

12.REPLACE HEATED OXYGEN SENSOR

NG

15.REPLACE AIR FUEL RATIO SENSOR
7.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / O2S B1S2 or O2S B2S2.


f.

Change the fuel injection volume using the GTS, monitoring the voltage output of the heated oxygen sensor displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of - 12% to +12%. The injection volume can be changed in fine gradations within this range.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.




OK

8.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)

NG

9.CHECK FOR EXHAUST GAS LEAK
8.PERFORM ACTIVE TEST USING GTS (INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.


f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations within this range.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the GTS.



Result
GTS Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio sensor)
Alternates between higher than and below 3.3 V OK
Remains at higher than 3.3 V NG
Remains at below 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either below or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E04
5.875,2.458 6.188,1.479 false 5.552,2.271 6.188,1.479 false 5.719,1.667 6.188,1.479 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.396,1.865 4.094,1.698 false 3.531,2.729 3.208,2.927 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 3.3 V 2.656,0.26 3.083,0.458 0.427,0.198 10 +12% 4.125,1.125 4.51,1.323 0.385,0.198 10 -12% 1.656,2.854 1.906,3.052 0.25,0.198 10 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 Malfunction 5.854,2.615 6.583,2.792 0.729,0.177 10 Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 Injection Volume 3.583,2.635 5.583,2.781 2,0.146 10 Heated Oxygen Sensor Output 6.229,1.219 7.156,1.906 0.927,0.688 10 Air Fuel Ratio Sensor Output 4.406,1.813 4.896,1.979 0.49,0.167 10 Normal



OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO AND REPAIR CAUSE (FUEL INJECTOR, FUEL PRESSURE, GAS LEAK FROM SYSTEM, ETC.)

NG

15.REPLACE AIR FUEL RATIO SENSOR
9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leakage.

OK:

No gas leak.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C27-1 (HT1B) - C37-18 (HT1B) Always Below 1 Ω
C27-3 (OX1B) - C35-9 (OX1B) Always Below 1 Ω
C27-4 (E2) - C35-10 (EX1B) Always Below 1 Ω
C145-1 (HT2B) - C37-13 (HT2B) Always Below 1 Ω
C145-3 (OX2B) - C35-3 (OX2B) Always Below 1 Ω
C145-4 (E2) - C35-4 (EX2B) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C27-1 (HT1B) - C37-12 (HT1B) Always Below 1 Ω
C27-3 (OX1B) - C34-2 (OX1B) Always Below 1 Ω
C27-4 (E2) - C34-1 (EX1B) Always Below 1 Ω
C28-1 (HT2B) - C37-13 (HT2B) Always Below 1 Ω
C28-3 (OX2B) - C34-4 (OX2B) Always Below 1 Ω
C28-4 (E2) - C34-3 (EX2B) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C27-1 (HT1B) or C37-18 (HT1B) - Body ground Always 10 kΩ or higher
C27-3 (OX1B) or C35-9 (OX1B) - Body ground Always 10 kΩ or higher
C27-4 (E2) or C35-10 (EX1B) - Body ground Always 10 kΩ or higher
C145-1 (HT2B) or C37-13 (HT2B) - Body ground Always 10 kΩ or higher
C145-3 (OX2B) or C35-3 (OX2B) - Body ground Always 10 kΩ or higher
C145-4 (E2) or C35-4 (EX2B) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C27-1 (HT1B) or C37-12 (HT1B) - Body ground Always 10 kΩ or higher
C27-3 (OX1B) or C34-2 (OX1B) - Body ground Always 10 kΩ or higher
C27-4 (E2) or C34-1 (EX1B) - Body ground Always 10 kΩ or higher
C28-1 (HT2B) or C37-13 (HT2B) - Body ground Always 10 kΩ or higher
C28-3 (OX2B) or C34-4 (OX2B) - Body ground Always 10 kΩ or higher
C28-4 (E2) or C34-3 (EX2B) - Body ground Always 10 kΩ or higher



A182248E13
0.188,0.115 4.073,0.313 3.885,0.198 12 false Reference (System Diagram of Sensor 2): 0.292,1.01 0.979,1.5 0.688,0.49 10 false from Battery 1.302,1.24 1.594,1.438 0.292,0.198 10 false EFI 2.26,2.104 2.542,2.302 0.281,0.198 10 false EFI 0.75,3.313 1.406,3.51 0.656,0.198 10 false Ground 4.063,0.771 4.698,0.969 0.635,0.198 10 false Heater 4.063,1.406 4.698,1.604 0.635,0.198 10 false Sensor 3.635,2.094 5.26,2.292 1.625,0.198 10 false Heated Oxygen Sensor 4.708,1.594 5.24,1.792 0.531,0.198 10 false OX1B 5.302,1.594 5.833,1.792 0.531,0.198 10 false OX1B 5.302,2.24 5.708,2.438 0.406,0.198 10 false EX1B 5.302,2.677 5.833,2.875 0.531,0.198 10 false MREL 5.302,0.948 5.833,1.146 0.531,0.198 10 false HT1B 3.698,0.948 3.958,1.146 0.26,0.198 10 false +B 3.698,1.594 3.958,1.792 0.26,0.198 10 false E2 4.719,0.948 5.115,1.146 0.396,0.198 10 false HT1B 6.01,3.24 6.427,3.438 0.417,0.198 10 false ECM 6.406,1.813 6.927,2.208 0.521,0.396 10 false Duty Control 3.021,1.271 3.667,1.417 0.646,0.146 10 false EFI No. 2

d.

Reconnect the heated oxygen sensor connector.


e.

Reconnect the ECM connector.



OK

12.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

12.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

13.PERFORM CONFIRMATION DRIVING PATTERN
13.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Refer to Confirmation Driving Pattern.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again by accelerating the vehicle and using the second gear to decelerate the vehicle.

Result
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0136, P0137, P0138, P0156, P0157 or P0158 stored)
B

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

END

B

15.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Refer to Confirmation Driving Pattern.



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again by accelerating the vehicle and using the second gear to decelerate the vehicle.

Result
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0136, P0137, P0138, P0156, P0157 or P0158 stored)
B



A

END

B