28300
1.INSPECT STARTER RELAY (ST)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the relay.
28610
2.INSPECT GLOW PLUG RELAY (GLOW)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the relay.
85935
3.INSPECT FUEL PUMP RELAY (FUEL PMP)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the relay.
82641
4.INSPECT NO. 1 INTEGRATION RELAY (IG2)
Check the IG2 fuse.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 fuse | Always | Below 1 Ω |
If the result is not as specified, replace the IG2 fuse.
Check the IG2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1C-1 - 1H-4 | Battery voltage not applied to terminals 1H-1 and 1H-3 | 10 kΩ or higher |
| Battery voltage applied to terminals 1H-1 and 1H-3 | Below 1 Ω |
| *a | Component without harness connected
(Integration Relay) |
If the result is not as specified, replace the integration relay.
82641
5.INSPECT NO. 1 INTEGRATION RELAY (EFI)
Check the EFI fuse.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI fuse | Always | Below 1 Ω |
If the result is not as specified, replace the EFI fuse.
Check the EFI relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1C-1 - 1I-4 | Battery voltage not applied to terminals 1I-2 and 1I-3 | 10 kΩ or higher |
| Battery voltage applied to terminals 1I-2 and 1I-3 | Below 1 Ω |
| *a | Component without harness connected
(Integration Relay) |
If the result is not as specified, replace the integration relay.
6.INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)
The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).
Inspect the ACC relay.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Main Body ECU) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2D-17 - 2K-1 | Battery voltage not applied to terminals 2A-48 and 2D-4 | 10 kΩ or higher |
| Battery voltage applied to terminals 2A-48 and 2D-4 | Below 1 Ω |
If the result is not as specified, replace the main body ECU.
Inspect the IG1 No. 1 relay.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Main Body ECU) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2A-31 - 2K-1 | Battery voltage not applied to terminals 2A-52 and 2D-4 | 10 kΩ or higher |
| Battery voltage applied to terminals 2A-52 and 2D-4 | Below 1 Ω |
If the result is not as specified, replace the main body ECU.