Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM J

5L-E ENGINE CONTROL  ECD SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes current to flow to the EFI relay coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A227838E05
5.51,2.031 5.74,2.229 0.229,0.198 10 false 11 5.542,3.25 5.667,3.448 0.125,0.198 10 false 1 5.51,3.656 5.698,3.854 0.188,0.198 10 false 10 5.552,4.167 5.75,4.365 0.198,0.198 10 false 5 5.396,2.26 5.781,2.438 0.385,0.177 10 false G183 5.396,3.469 5.76,3.646 0.365,0.177 10 false G183 5.406,3.844 5.781,4.021 0.375,0.177 10 false G183 5.406,4.375 5.854,4.552 0.448,0.177 10 false C161 4.125,2.25 4.365,2.427 0.24,0.177 10 false 1A 4.125,2.635 4.365,2.813 0.24,0.177 10 false 1A 4.125,3.021 4.365,3.198 0.24,0.177 10 false 1A 4.125,3.479 4.365,3.656 0.24,0.177 10 false 1B 4.125,3.865 4.365,4.042 0.24,0.177 10 false 1B 4.177,2.063 4.333,2.229 0.156,0.167 10 false 5 4.177,2.438 4.333,2.604 0.156,0.167 10 false 1 4.177,2.823 4.302,2.99 0.125,0.167 10 false 3 4.177,3.271 4.333,3.438 0.156,0.167 10 false 4 4.177,3.656 4.333,3.823 0.156,0.167 10 false 2 6.198,4.927 6.583,5.115 0.385,0.188 10 false ECM 1.49,2.26 1.729,2.448 0.24,0.188 10 false 1C 1.5,3.865 1.74,4.042 0.24,0.177 10 false 1B 1.542,3.656 1.667,3.823 0.125,0.167 10 false 3 1.542,2.052 1.698,2.219 0.156,0.167 10 false 1 2.417,3.615 2.688,3.792 0.271,0.177 10 false EFI 2.417,2.396 2.688,2.594 0.271,0.198 10 false IG2 0.708,2.438 1.073,2.615 0.365,0.177 10 false P/I-B 0.771,0.938 1.021,1.115 0.25,0.177 10 false ST 2.104,1.104 2.375,1.281 0.271,0.177 10 false G2 2,0.625 2.135,0.813 0.135,0.188 10 false 7 3.042,0.625 3.177,0.813 0.135,0.188 10 false 6 3.49,2.938 3.76,3.135 0.271,0.198 10 false IG2 3.49,4.156 3.76,4.333 0.271,0.177 10 false EFI 0.635,4.271 1.135,4.427 0.5,0.156 10 false Battery 2.104,1.26 3.344,1.458 1.24,0.198 10 false Ignition Switch 5.833,2.125 6.302,2.313 0.469,0.188 10 false IGSW 4.938,2.417 5.406,2.604 0.469,0.188 10 false IGN 5.854,3.458 6.323,3.646 0.469,0.188 10 false +B 5.854,3.813 6.323,4 0.469,0.188 10 false MREL 5.854,4.354 6.323,4.542 0.469,0.188 10 false E1 2.167,0.885 2.531,1.083 0.365,0.198 10 false AM2 2.729,0.885 3.094,1.083 0.365,0.198 10 false IG2 2.125,4.573 3.573,4.76 1.448,0.188 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ECM (+B VOLTAGE)
U169093E02
0.667,0.792 1,1.531 false 2.979,0.781 2.438,1.542 false 2.573,0.344 3.01,0.51 0.438,0.167 10 false G183 0.135,0.052 0.365,0.219 0.229,0.167 10 false *a 2.219,1.563 2.698,1.75 0.479,0.188 10 false 1 (+B) 0.833,1.573 1.458,1.76 0.625,0.188 10 false 5 (E1) 0.563,0.344 1,0.51 0.438,0.167 10 false C161

a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G183-1 (+B) - C161-5 (E1) Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C161-5 (E1) - Body ground Always Below 1 Ω



c.

Reconnect the ECM connector.



OK

3.CHECK ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (IGSW VOLTAGE)
U169094E02
0.667,0.792 1,1.531 false 2.833,0.885 2.448,1.552 false 2.563,0.344 3,0.51 0.438,0.167 10 false G183 0.135,0.052 0.365,0.219 0.229,0.167 10 false *a 1.99,1.563 2.688,1.75 0.698,0.188 10 false 11 (IGSW) 0.813,1.573 1.438,1.76 0.625,0.188 10 false 5 (E1) 0.573,0.344 1.01,0.51 0.438,0.167 10 false C161

a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G183-11 (IGSW) - C161-5 (E1) Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

4.CHECK ECM (MREL VOLTAGE)

NG

7.INSPECT IGNITION SWITCH ASSEMBLY
4.CHECK ECM (MREL VOLTAGE)
U169095E02
0.667,0.792 1,1.531 false 2.885,0.885 2.438,1.552 false 2.573,0.354 3.01,0.521 0.438,0.167 10 false G183 0.135,0.052 0.365,0.219 0.229,0.167 10 false *a 2.021,1.563 2.729,1.75 0.708,0.188 10 false 10 (MREL) 0.813,1.563 1.438,1.75 0.625,0.188 10 false 5 (E1) 0.583,0.344 1.021,0.51 0.438,0.167 10 false C161

a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G186-10 (MREL) - C161-5 (E1) Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

5.CHECK NO. 1 INTEGRATION RELAY (EFI)

NG

5.CHECK NO. 1 INTEGRATION RELAY (EFI)
U170775E02
1.823,0.896 1.938,1.094 0.115,0.198 10 false 1 1.719,0.938 1.802,1.083 0.083,0.146 7 false 2 1.625,0.938 1.708,1.083 0.083,0.146 7 false 3 1.49,0.896 1.604,1.094 0.115,0.198 10 false 4 1.365,0.896 1.479,1.094 0.115,0.198 10 false 5 1.25,0.938 1.333,1.083 0.083,0.146 7 false 6 1.167,0.938 1.25,1.083 0.083,0.146 7 false 7 1.042,0.896 1.156,1.094 0.115,0.198 10 false 8 1.344,0.354 1.552,0.552 0.208,0.198 10 false 1B 1.042,1.74 2.542,1.938 1.5,0.198 10 false No. 1 Integration Relay

a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1B-4 - Body ground Ignition switch ON 10 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Integration Relay)


c.

Reconnect the No. 1 integration relay (EFI) connector.



OK

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI) - ECM AND BODY GROUND)

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI)

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI) - ECM AND BODY GROUND)
a.

Disconnect the No. 1 integration relay (EFI) connector from the engine room junction block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-2 - G183-10 (MREL) Always Below 1 Ω
1B-4 - G183-1 (+B) Always Below 1 Ω
1B-3 - Body ground Always Below 1 Ω
1B-2 or G183-10 (MREL) - Body ground Always 10 kΩ or higher
1B-4 or G183-1 (+B) - Body ground Always 10 kΩ or higher



d.

Reconnect the No. 1 integration relay connector.


e.

Reconnect the ECM connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TERMINAL +B OF ECM - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>5L-E (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM)

NG

REPLACE IGNITION SWITCH ASSEMBLY