Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM J

5L-E ENGINE CONTROL  ECD SYSTEM  Starter Signal Circuit  


DESCRIPTION

When the engine is cranked, the intake air flow becomes slow so fuel vaporization is poor. A rich mixture is therefore necessary in order to achieve good startability. While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel injection volume for starting and after-start injection control.

WIRING DIAGRAM

A362205E02
2.604,2.167 3.667,2.385 1.063,0.219 10 false Ignition Switch 2.604,2 3.667,2.219 1.063,0.219 10 false G2 2.635,1.021 3.031,1.208 0.396,0.188 10 false AM1 3.208,1.01 3.604,1.198 0.396,0.188 10 false ST1 2.646,1.719 3.042,1.906 0.396,0.188 10 false AM2 3.198,1.719 3.594,1.906 0.396,0.188 10 false ST2 1.625,1.052 2.021,1.24 0.396,0.188 10 false AM1 0.823,1.073 1.219,1.26 0.396,0.188 10 false ALT 0.823,1.771 1.219,1.958 0.396,0.188 10 false ST 3.031,4.802 3.427,4.99 0.396,0.188 10 false ST 2.448,0.771 2.844,0.958 0.396,0.188 10 false 2 3.583,0.781 3.979,0.969 0.396,0.188 10 false 1 2.448,1.448 2.844,1.635 0.396,0.188 10 false 7 3.573,1.458 3.969,1.646 0.396,0.188 10 false 8 2.698,4.354 3.094,4.542 0.396,0.188 10 false 1 3.521,4.365 3.917,4.552 0.396,0.188 10 false 2 3.531,3.833 3.927,4.021 0.396,0.188 10 false 5 2.698,3.833 3.094,4.021 0.396,0.188 10 false 3 5.438,1.469 5.594,1.656 0.156,0.188 10 false 2 5.438,2.167 5.573,2.365 0.135,0.198 10 false 1 5.833,1.677 6.854,1.885 1.021,0.208 10 false A41*1, r2*2 5.823,1.854 6.917,2.417 1.094,0.563 10 false Clutch Start Switch Assembly 1.417,4.698 1.813,4.885 0.396,0.188 10 false C95 0.719,4.979 1.115,5.167 0.396,0.188 10 false D5 1.24,4.688 1.646,4.896 0.406,0.208 10 false 1 0.771,4.781 1.177,4.99 0.406,0.208 10 false 1 1.146,5.802 1.75,6.042 0.604,0.24 10 false Starter 0.542,6.458 1.146,6.698 0.604,0.24 10 false Battery 3.76,6.188 4.688,6.385 0.927,0.198 10 false *1: for LHD 3.74,6.583 4.667,6.781 0.927,0.198 10 false *2: for RHD 6.083,4.5 6.479,4.688 0.396,0.188 10 false G182 6.083,5.979 6.479,6.167 0.396,0.188 10 false C161 6.208,5.792 6.604,5.979 0.396,0.188 10 false 5 6.24,4.313 6.635,4.5 0.396,0.188 10 false 6 6.5,4.49 6.896,4.677 0.396,0.188 10 false STA 6.51,5.979 6.906,6.167 0.396,0.188 10 false E1 6.563,6.438 6.958,6.625 0.396,0.188 10 false ECM

When using intelligent tester:

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Read the STA signal on the intelligent tester while the starter operates.

OK:
Ignition Switch Position Starter SIG
LOCK, ACC, ON OFF
START ON




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ECM)
2.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ECM)
a.

Disconnect the clutch start switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A41-1 - G182-6 (STA) Always Below 1 Ω
A41-1 or G182-6 (STA) - Body ground Always 10 kΩ higher

for RHD
Tester Connection Condition Specified Condition
r2-1 - G182-6 (STA) Always Below 1 Ω
r2-1 or G182-6 (STA) - Body ground Always 10 kΩ higher



d.

Reconnect the clutch start switch connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR