Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  


DESCRIPTION

The engine speed sensor in the engine control system contains a signal plate and a pickup coil for the NE signal. The NE signal plate has 56 teeth and is mounted in the injection or supply pump assembly. The NE signal sensor generates 56 signals for every 2 engine revolutions. The ECM detects the engine speed and the cam lift position of the injection or supply pump assembly. The ECM uses the TDC and NE signals for injection timing control. The NE signal is also used for injection volume control.

DTC No. DTC Detection Condition Trouble Area
P0335 No NE signal to ECM for 0.5 seconds or more at 680 rpm or more.
·

Open or short in engine speed sensor circuit

·

Injection or supply pump assembly

·

ECM


No NE signal to ECM for 2.0 seconds or more during cranking.

WIRING DIAGRAM

A311405E05
0.533,3.226 0.972,3.400 0.438,0.173 10 C103 0.466,0.212 0.897,0.385 0.432,0.173 10 C109 5.708,3.71 6.066,3.883 0.359,0.173 10 ECM 5.241,0.782 5.675,0.955 0.434,0.173 10 TDC+ 4.928,0.775 5.144,0.948 0.217,0.173 10 26 4.928,1.369 5.144,1.543 0.217,0.173 10 34 4.928,2.202 5.144,2.376 0.217,0.173 10 27 4.928,2.791 5.144,2.964 0.217,0.173 10 35 5.69,3.519 6.062,3.692 0.372,0.173 10 C162 5.241,1.371 5.659,1.545 0.418,0.173 10 TDC- 5.241,2.207 5.600,2.380 0.359,0.173 10 NE+ 5.241,2.796 5.559,2.970 0.318,0.173 10 NE- 1.923,0.765 2.074,0.938 0.151,0.173 10 1 1.923,2.78 2.058,2.954 0.134,0.173 10 1 1.923,1.347 2.047,1.521 0.123,0.173 10 2 1.923,2.217 2.074,2.391 0.151,0.173 10 2 0.456,0.38 2.202,0.554 1.746,0.173 10 Crankshaft Position Sensor 3.17,3.193 3.320,3.442 0.150,0.249 10 * 0.536,3.394 2.212,3.920 1.677,0.526 10 Engine Speed Sensor (inside the Injection or Supply Pump Assembly) 2.723,3.992 3.531,4.168 0.809,0.177 10 *: Shielded 3.17,1.778 3.320,2.027 0.150,0.249 10 *

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ENGINE SPEED SENSOR
a.

Check the engine speed sensor installation.


b.

Inspect the engine speed sensor (See page Engine / Hybrid System>5L-E (FUEL)>FUEL INJECTION PUMP>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (ECM - ENGINE SPEED SENSOR)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (ECM - ENGINE SPEED SENSOR)
a.

Disconnect the engine speed sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C103-2 - C162-27 (NE+) Always Below 1 Ω
C103-1 - C162-35 (NE-) Always Below 1 Ω
C103-2 or C162-27 (NE+) - Body ground Always 10 kΩ or higher
C103-1 or C162-35 (NE-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR