Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P0115  Engine Coolant Temperature Circuit  


DESCRIPTION

The engine coolant temperature sensor senses the coolant temperature. A thermistor built into the sensor changes the resistance value according to the coolant temperature. The lower the coolant temperature, the greater the thermistor resistance value, and the higher the coolant temperature, the lower the thermistor resistance value (See Fig. 1).

The engine coolant temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the engine coolant temperature sensor from the terminal THW via a resistor R. That is, the resistor R and the engine coolant temperature sensor are connected in series. When the resistance value of the engine coolant temperature sensor changes in accordance with changes in the coolant temperature, the potential at the terminal THW also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during cold engine operation.

A208462E46
1.49,2 1.646,1.76 1.646,1.76 1.792,1.76 false 0.208,0.146 0.75,0.385 0.542,0.24 10 false (Fig. 1) 0.208,0.542 1.229,0.781 1.021,0.24 10 false Resistance kΩ 1.823,1.667 2.604,1.875 0.781,0.208 10 false Acceptable 1.604,4.063 2.656,4.313 1.052,0.25 10 false Temp. °C (°F)

DTC No. DTC Detection Condition Trouble Area
P0115 Open or short in engine coolant temperature sensor circuit for 0.5 seconds or more.
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM



WIRING DIAGRAM

A311404E13
0.207,1.999 0.613,2.174 0.406,0.175 10 C111 5.97,2.462 6.336,2.637 0.366,0.175 10 ECM 5.947,2.307 6.355,2.482 0.408,0.175 10 C162 5.21,1.335 5.429,1.510 0.219,0.175 10 29 5.21,0.76 5.429,0.935 0.219,0.175 10 21 6.077,0.365 6.313,0.540 0.235,0.175 10 5 V 6.006,0.629 6.195,0.804 0.189,0.175 10 R 2.011,0.759 2.200,0.934 0.189,0.175 10 2 2.011,1.327 2.200,1.502 0.189,0.175 10 1 5.436,0.746 5.816,0.921 0.379,0.175 10 THW 5.436,1.323 5.923,1.498 0.487,0.175 10 ETHW 0.207,2.168 2.534,2.343 2.327,0.175 10 Engine Coolant Temperature Sensor

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


d.

Read the value.

Result:
Display Proceed
-40°C (-40°F) A
140°C (284°F) or more B
The same as actual engine coolant temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (- 40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

B

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

C

2.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)
a.
U169149E02
0.656,0.323 0.854,0.521 0.198,0.198 10 false *1 0.198,2.552 0.375,2.75 0.177,0.198 10 false *a 2.406,1.729 2.927,1.948 0.521,0.219 10 false ETHW 2.552,0.302 2.74,0.531 0.188,0.229 10 false *2 2.417,1.26 2.865,1.49 0.448,0.229 10 false THW 0.677,3.5 1.052,3.646 0.375,0.146 10 false C111

Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the ECT sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value.

OK:

140°C (284°F) or higher


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
3.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C111-2 - C162-21 (THW) Always Below 1 Ω
C111-1 - C162-29 (ETHW) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.
A302633E05
2.469,1.063 2.917,1.323 0.448,0.26 10 false THW 2.479,1.51 3,1.708 0.521,0.198 10 false ETHW 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2

Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


e.

Read the value.

OK:

-40°C (-40°F)


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM



OK

NG

5.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C111-2 or C162-21 (THW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR