Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P0105  Manifold Absolute Pressure / Barometric Pressure Circuit  


DESCRIPTION

The manifold absolute pressure sensor generates voltage by the vacuum value as shown in the illustration. This voltage of the manifold absolute pressure sensor is one of the factors used to decide the injection volume and injection timing.

A006532E20
0.385,0.469 0.5,0.667 0.115,0.198 10 false V 0.302,0.781 0.521,0.979 0.219,0.198 10 false 4.5 0.271,1.875 0.51,2.073 0.24,0.198 10 false 0.5 1,2.323 1.292,2.521 0.292,0.198 10 false 60.0 2.26,2.333 2.635,2.531 0.375,0.198 10 false 206.7 2.896,2.125 3.167,2.323 0.271,0.198 10 false kPa 2.896,2.51 3.354,2.708 0.458,0.198 10 false mmHg 2.885,2.854 3.333,3.052 0.448,0.198 10 false (in.Hg) 2.24,2.688 2.729,2.885 0.49,0.198 10 false 1,550 0.958,2.854 1.49,3.021 0.531,0.167 10 false (17.7) 1.281,3.073 2.083,3.271 0.802,0.198 10 false Air Pressure 0.99,2.698 1.333,2.917 0.344,0.219 10 false 450 2.24,2.865 2.729,3.115 0.49,0.25 10 false (61.0)

DTC No. DTC Detection Condition Trouble Area
P0105 Open or short in manifold absolute pressure sensor circuit for 2 seconds or more.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



WIRING DIAGRAM

A311403E04
0.585,2.912 1.007,3.087 0.421,0.175 10 C83 5.547,3.29 5.912,3.465 0.366,0.175 10 ECM 1.701,0.947 1.949,1.122 0.248,0.175 10 VC 4.732,2.138 4.945,2.313 0.213,0.175 10 32 4.732,1.478 4.964,1.653 0.231,0.175 10 33 4.732,0.885 4.936,1.060 0.204,0.175 10 24 2.043,2.119 2.163,2.294 0.120,0.175 10 1 2.043,0.856 2.163,1.031 0.120,0.175 10 3 2.043,1.48 2.163,1.655 0.120,0.175 10 2 6.035,0.676 6.270,0.851 0.235,0.175 10 5 V 1.797,2.22 1.950,2.395 0.153,0.175 10 E 1.65,1.578 1.957,1.754 0.307,0.175 10 PIM 4.997,0.845 5.556,1.020 0.559,0.175 10 VCPM 4.997,1.49 5.304,1.665 0.307,0.175 10 PIM 4.997,2.111 5.441,2.286 0.444,0.175 10 EPIM 0.586,3.081 2.826,3.256 2.241,0.175 10 Manifold Absolute Pressure Sensor 5.533,3.117 5.954,3.292 0.421,0.175 10 G183

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.


d.

Read the value.

OK:

The same as atmospheric pressure.


HINT:

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).


Intake Manifold Pressure (kPa) Malfunction
Approx. 0
·

Open in VC circuit

·

Short in PIM circuit


192 or more
·

Open in PIM circuit

·

Open in E2 circuit





OK

2.CHECK CONNECTION OF VACUUM HOSE

NG

3.CHECK HARNESS AND CONNECTOR (ECM - MANIFOLD ABSOLUTE PRESSURE SENSOR)
2.CHECK CONNECTION OF VACUUM HOSE
a.

Check that the vacuum hose is securely connected and there are no leaks from the connection.

OK:

The vacuum hose is securely connected and there are no leaks from the connection.




OK

3.CHECK HARNESS AND CONNECTOR (ECM - MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

REPAIR OR REPLACE VACUUM HOSE

3.CHECK HARNESS AND CONNECTOR (ECM - MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C83-2 (PIM) - G183-33 (PIM) Always Below 1 Ω
C83-3 (VC) - G183-24 (VCPM) Always Below 1 Ω
C83-1 (E) - G183-32 (EPIM) Always Below 1 Ω
C83-2 (PIM) or G183-33 (PIM) - Body ground Always 10 kΩ or higher
C83-3 (VC) or G183-24 (VCPM) - Body ground Always 10 kΩ or higher




OK

4.INSPECT ECM (CHECK VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ECM (CHECK VOLTAGE)
a.
U169123E01
1.096,1.73 1.211,1.885 0.115,0.154 10 E 2.206,1.697 2.479,1.852 0.273,0.154 10 VC 0.241,0.222 0.425,0.391 0.184,0.170 10 *a 1.485,1.286 1.199,1.702 false 1.945,1.286 2.187,1.688 false 0.622,1.089 0.902,1.231 0.281,0.142 10 C83

Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C83-3 (VC) - C83-1 (E) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)



OK

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.



NEXT

6.READ OUTPUT DTC (DTC P0105 IS OUTPUT AGAIN)
6.READ OUTPUT DTC (DTC P0105 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Turn the ignition switch to ON.


e.

Check the DTC (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).

Result:
Display (DTC output) Proceed to
DTC P0105 is output again A
No DTC output B




A

B

END