Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1120  Throttle / Pedal Position Sensor/Coolant Flow Control Valve Position Sensor Circuit  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal position sensor.

·

The electrical throttle system does not use a throttle cable.

·

The accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted in the accelerator pedal to detect the opening angle of the accelerator pedal. Since this sensor is electronically controlled with hall elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.

In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V, in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting a malfunction. The ECM judges the current opening angle of the accelerator pedal from these signals input from terminals VPA and VPA2, and the ECM controls the injection pump based on these signals.

A255815E54
4.333,2.031 4.208,1.948 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.229,2.333 false 4.344,2.396 4.229,2.51 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.854,2.26 0.385,0.938 0.385,0.938 0.5,0.938 true 4.333,1.833 3.844,0.938 false 0.958,2.833 0.823,1.219 0.823,1.219 0.938,1.219 true 1.042,2.542 1.063,1.448 1.063,1.448 1.177,1.448 true 0.385,3.833 2.198,4.208 1.813,0.375 10 false Accelerator Pedal Sensor 0.573,0.833 1.052,1.01 0.479,0.177 10 false Magnet 0.99,1.115 1.521,1.292 0.531,0.177 10 false No. 2 IC 2.063,1.74 2.531,1.917 0.469,0.177 10 false VPA 2.063,2.073 2.552,2.271 0.49,0.198 10 false EPA 2.063,2.385 2.583,2.563 0.521,0.177 10 false VCPA 2.063,2.688 2.573,2.865 0.51,0.177 10 false VPA2 2.063,3 2.563,3.198 0.5,0.198 10 false EPA2 2.063,3.323 2.583,3.5 0.521,0.177 10 false VCP2 2.698,1.344 3.021,1.521 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.854 4.208,2.031 0.292,0.177 10 false 4.55 3.844,2.063 4.208,2.24 0.365,0.177 10 false 3.988 3.938,2.281 4.229,2.458 0.292,0.177 10 false 3.75 3.875,2.469 4.24,2.646 0.365,0.177 10 false 3.188 3.969,2.823 4.271,3 0.302,0.177 10 false 1.6 3.979,3.042 4.281,3.219 0.302,0.177 10 false 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.281,3.823 0.5,0.229 10 false 15.9 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.656,3.938 6.76,4.167 2.104,0.229 10 false Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.156,0.813 3.854,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.479,2.281 6.927,2.51 0.448,0.229 10 false VPA 6.438,1.823 6.865,2 0.427,0.177 10 false VPA2 1.24,1.375 1.771,1.552 0.531,0.177 10 false No. 1 IC

DTC No. DTC Detection Condition Trouble Area
P1120 Condition (a), (b), (c) or (d) continues for 2.0 seconds:
(a) VPA is 0.2 V or less and VPA2 is 0.5 V or less.
(b) VPA is 4.8 V or higher.
(c) VPA2 is 4.8 V or higher, and VPA is between 0.4 V and 3.45 V.
(d) The difference between VPA and VPA2 is 0.02 V or less.
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal rod assembly

·

ECM


Condition (a) continues for 0.5 seconds:
(a) VPA is 0.2 V or less or VPA2 is 0.5 V or less.

WIRING DIAGRAM

A149601E45
0.278,3.17 2.433,3.376 2.155,0.206 10 Accelerator Pedal Position Sensor 5.6,1.226 6.060,1.431 0.460,0.206 10 VCPA 5.332,1.22 5.510,1.426 0.179,0.206 10 26 5.334,0.367 5.513,0.573 0.179,0.206 10 20 5.341,2.49 5.520,2.695 0.179,0.206 10 23 5.334,0.8 5.513,1.005 0.179,0.206 10 27 5.338,1.654 5.517,1.859 0.179,0.205 10 28 5.334,2.081 5.513,2.287 0.179,0.206 10 29 5.6,0.382 5.997,0.587 0.398,0.206 10 VPA 5.6,0.791 6.049,0.997 0.450,0.206 10 EPA 5.6,2.502 6.042,2.707 0.443,0.205 10 VCP2 5.6,1.63 6.035,1.836 0.436,0.206 10 VPA2 5.6,2.052 6.188,2.257 0.588,0.206 10 EPA2 1.503,1.309 1.963,1.515 0.460,0.206 10 VCPA 1.571,0.465 1.885,0.671 0.314,0.206 10 VPA 1.571,0.895 1.918,1.100 0.348,0.206 10 EPA 1.503,2.585 1.946,2.790 0.443,0.205 10 VCP2 1.503,1.737 1.939,1.943 0.436,0.206 10 VPA2 1.503,2.155 1.929,2.361 0.426,0.206 10 EPA2 1.99,1.172 2.197,1.378 0.207,0.206 10 4 1.99,0.353 2.197,0.559 0.207,0.206 10 6 1.99,0.772 2.197,0.977 0.207,0.206 10 5 1.99,2.474 2.197,2.680 0.207,0.206 10 1 1.99,1.621 2.197,1.826 0.207,0.206 10 3 1.99,2.043 2.197,2.248 0.207,0.206 10 2 5.978,3.17 6.371,3.371 0.393,0.201 10 ECM 5.978,3.015 6.403,3.193 0.425,0.178 10 G183 0.278,3.008 0.646,3.194 0.368,0.186 10 A19

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION)
a.
FI07052E64
0.5,1.781 1.188,1.979 0.688,0.198 10 false Depressed 2.427,1.781 3.031,1.979 0.604,0.198 10 false Released

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.


d.

Read the values.

OK:

Check that the value displayed on the GTS changes by repeatedly depressing and releasing the accelerator pedal.




OK

2.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)

NG

3.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
2.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)

b.

Start the engine.


c.

Idle the engine for 15 seconds or more.


d.

Read the DTC (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).

Result:
Display (DTC output) Proceed to
DTC P1120 is output again A
No DTC output B




A

B

SYSTEM OK

3.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A19-1 (VCP2) - G183-23 (VCP2) Always Below 1 Ω
A19-2 (EPA2) - G183-29 (EPA2) Always Below 1 Ω
A19-3 (VPA2) - G183-28 (VPA2) Always Below 1 Ω
A19-4 (VCPA) - G183-26 (VCPA) Always Below 1 Ω
A19-5 (EPA) - G183-27 (EPA) Always Below 1 Ω
A19-6 (VPA) - G183-20 (VPA) Always Below 1 Ω
A19-1 (VCP2) or G183-23 (VCP2) - Body ground Always 10 kΩ or higher
A19-2 (EPA2) or G183-29 (EPA2) - Body ground Always 10 kΩ or higher
A19-3 (VPA2) or G183-28 (VPA2) - Body ground Always 10 kΩ or higher
A19-4 (VCPA) or G183-26 (VCPA) - Body ground Always 10 kΩ or higher
A19-5 (EPA) or G183-27 (EPA) - Body ground Always 10 kΩ or higher
A19-6 (VPA) or G183-20 (VPA) - Body ground Always 10 kΩ or higher




OK

4.INSPECT ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ECM (VCPA AND VCP2 VOLTAGE)
a.
U169381E02
1.365,1.281 0.75,1.823 false 1.5,1.292 1.406,1.823 false 1.844,1.292 2.073,1.813 false 2,1.281 2.729,1.823 false 1.167,1.885 1.563,2.063 0.396,0.177 10 false EPA2 1.854,1.865 2.25,2.042 0.396,0.177 10 false VCPA 0.385,1.865 0.76,2.042 0.375,0.177 10 false VCP2 0.198,0.135 0.354,0.313 0.156,0.177 10 false *a 2.667,1.865 3.021,2.042 0.354,0.177 10 false EPA 0.635,1.135 0.917,1.313 0.281,0.177 10 false A19

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A19-1 (VCP2) - A19-2 (EPA2) Ignition switch ON 4.5 to 5.5 V
A19-4 (VCPA) - A19-5 (EPA) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)



OK

5.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

5.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal rod assembly (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

6.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)
6.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)

b.

Start the engine.


c.

Idle the engine for 15 seconds or more.


d.

Read the DTC (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).

Result:
Display (DTC output) Proceed to
DTC P1120 is output again A
No DTC output B




A

B

SYSTEM OK