Home › Engine / Hybrid System › 5L-E (ENGINE CONTROL) › ECD SYSTEM
RM27T0E _51 Engine / Hybrid System _053658 5L-E ENGINE CONTROL _0260445 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1225  Spill Control Circuit  


DESCRIPTION

The ECM controls the fuel injection volume by operating the spill control valve. The spill control valve is mounted on the injection or supply pump assembly, and opens or closes the injection pressure releasing port with the solenoid valve in the spill control valve. During injection, the valve is closed (ON). The ECM decides the basic fuel injection volume by the engine speed and accelerator pedal opening angle, and calculates the final fuel injection angle to make the various corrections to the basic fuel injection volume. The ECM counts the NE signal to detect the angle from injection starts and operates the spill control valve from ON to OFF (the injection pressure releasing port is open) at the position that detects the final fuel injection angle.

U169071E02
2.521,1.625 3.615,1.625 false 2.406,2.323 2.406,2.458 false 0.313,0.531 1.167,0.75 0.854,0.219 10 false NE Signal 0.885,1.188 1.74,1.406 0.854,0.219 10 false Close (ON) 0.875,1.5 1.833,1.719 0.958,0.219 10 false Close (OFF) 0.031,1.344 0.5,1.906 0.469,0.563 10 false Spill Control Valve 0.656,1.813 1.448,2.177 0.792,0.365 10 false Plunger Lift 1.979,2.542 3.021,2.74 1.042,0.198 10 false Injection start 2.542,1.656 3.667,2.094 1.125,0.438 10 false Final fuel injection angle

DTC No. DTC Detection Condition Trouble Area
P1225 Open or short in spill control valve at 500 rpm or more.
·

Open or short in spill control valve circuit

·

Spill control valve (Injection or supply pump assembly)

·

ECM



WIRING DIAGRAM

A311406E03
0.703,1.852 1.077,2.003 0.374,0.151 10 C106 4.977,2.851 5.350,3.002 0.374,0.151 10 ECM 4.443,0.982 4.870,1.132 0.427,0.151 10 SPV+ 4.443,1.683 4.835,1.834 0.391,0.151 10 SPV- 4.443,2.151 4.656,2.301 0.213,0.151 10 E1 4.214,0.927 4.421,1.077 0.207,0.151 10 2 4.214,1.603 4.421,1.753 0.207,0.151 10 1 4.214,2.07 4.497,2.221 0.283,0.151 10 5 4.962,2.676 5.465,2.827 0.503,0.151 10 C161 1.809,0.91 1.939,1.060 0.131,0.151 10 2 1.809,1.575 1.939,1.726 0.131,0.151 10 1 0.685,2.014 1.852,2.165 1.167,0.151 10 Spill Control Valve

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT SPILL CONTROL VALVE
a.

Inspect the spill control valve (See page Engine / Hybrid System>5L-E (FUEL)>FUEL INJECTION PUMP>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (ECM - SPILL CONTROL VALVE)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (ECM - SPILL CONTROL VALVE)
a.

Disconnect the spill control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C106-2 - C161-2 (SPV+) Always Below 1 Ω
C106-1 - C161-1 (SPV-) Always Below 1 Ω
C106-2 or C161-2 (SPV+) - Body ground Always 10 kΩ or higher
C106-1 or C161-1 (SPV-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR