The intake air temperature sensor is built into the mass air flow meter and detects the intake air temperature.
A thermistor built into the sensor changes its resistance value according to the intake air temperature.
The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The intake air temperature sensor is connected to the ECM.
The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.
Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 0.5 seconds | Short in the IAT sensor for 0.5 seconds (1 trip detection logic). | ·
Short in IAT sensor circuit ·
IAT sensor (built into mass air flow meter) ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 0.5 seconds | Open in the IAT sensor for 0.5 seconds (1 trip detection logic). | ·
Open in IAT sensor circuit ·
IAT sensor (built into mass air flow meter) ·
ECM |
| DTC No. | Data List |
|---|---|
| P0112 | Intake Air |
| P0113 |
If DTC P0112 and/or P0113 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When DTC P0112 or P0113 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
Same as actual intake air temperature
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (same as actual intake air temperature) | C |
If there is an open circuit, the tester indicates -40°C (-40°F).
If there is a short circuit, the tester indicates 140°C (284°F) or higher.
A
B
C
Disconnect the mass air flow meter connector.
Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
140°C (284°F) or higher
| *1 | Mass air flow meter |
| *2 | ECM |
| *a | Front view of wire harness connector
(to mass air flow meter) |
Reconnect the mass air flow meter connector.
OK
NG
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C33-1 (THA) - C90-6 (THA) | Always | Below 1 Ω |
| C33-2 (E2) - C90-12 (ETHA) | Always | Below 1 Ω |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
OK
NG
Disconnect the mass air flow meter connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
-40°C (-40°F)
| *1 | Mass air flow meter |
| *2 | ECM |
Reconnect the mass air flow meter connector.
OK
NG
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C33-1 (THA) or C90-6 (THA) - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Replace the mass air flow meter (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
NEXT
Replace the mass air flow meter (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
NEXT