Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

P0560
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized (1 trip detection logic).
·

Open in backup power source circuit (to BATT terminal)

·

Battery

·

Battery terminals

·

EFI fuse

·

ECM



Related Data List
DTC No. Data List
P0560 Battery Voltage*

*: This is not the voltage of the BATT, it is the power supply voltage for the ECM.

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


WIRING DIAGRAM

A221594E03
5.552,0.807 5.958,0.991 0.406,0.184 10 BATT 5.559,1.316 5.850,1.486 0.290,0.170 10 +B2 5.565,1.857 5.806,2.024 0.242,0.167 10 +B 5.539,2.15 5.982,2.324 0.443,0.174 10 MREL 2.268,2.017 2.508,2.191 0.239,0.174 10 EFI 5.998,3.23 6.329,3.398 0.332,0.168 10 ECM 0.802,2.021 1.152,2.196 0.350,0.174 10 P/I-B 3.282,2.563 3.540,2.737 0.258,0.174 10 EFI 1.85,1.872 2.059,2.042 0.209,0.170 10 1C 3.972,2.235 4.190,2.398 0.218,0.163 10 1B 3.966,1.886 4.185,2.049 0.218,0.163 10 1B 2.69,1.308 2.908,1.471 0.218,0.163 10 1B 1.842,2.239 2.061,2.402 0.218,0.163 10 1B 1.902,1.683 2.047,1.856 0.145,0.173 10 1 2.974,1.304 3.119,1.478 0.145,0.173 10 1 4.024,1.697 4.125,1.853 0.100,0.156 10 4 1.893,2.412 2.021,2.574 0.128,0.163 10 3 4.024,2.419 4.125,2.568 0.100,0.149 10 2 5.257,0.653 5.438,0.812 0.180,0.159 10 23 5.236,1.157 5.441,1.313 0.205,0.156 10 17 5.243,1.704 5.420,1.867 0.177,0.163 10 24 5.236,2.075 5.426,2.238 0.190,0.163 10 11 1.734,2.967 4.947,3.144 3.214,0.177 10 No. 1 Integration Relay (Engine Room Relay Block) 5.197,0.83 5.502,0.976 0.304,0.147 10 G57 5.188,1.329 5.492,1.476 0.304,0.147 10 G57 5.193,1.876 5.497,2.022 0.304,0.147 10 G57 5.197,2.235 5.502,2.382 0.304,0.147 10 G58 0.559,2.712 1.322,2.887 0.762,0.174 10 Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When the ignition switch is turned to ON, even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, this DTC is stored.



PROCEDURE

1.CHECK ECM TERMINAL VOLTAGE (BATT)
a.
U169105E02
0.323,1.073 0.688,1.604 true 0.292,0.24 0.615,0.417 0.323,0.177 10 false G57 0.031,0 0.26,0.177 0.229,0.177 10 false *a 0.375,1.635 1.125,1.865 0.75,0.229 10 false 23 (BATT)

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G57-23 (BATT) - Body ground Always 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)


c.

Reconnect the ECM connector.



OK

2.INSPECT BATTERY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.




OK

3.CHECK BATTERY TERMINAL

NG

7.RECHARGE OR REPLACE BATTERY
3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

8.REPAIR OR REPLACE BATTERY TERMINAL
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON for 3 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read the DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

5.REPLACE ECM

B

END

5.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE BATTERY TERMINAL
a.

Repair or replace the battery terminal.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 3 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END