Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal position sensor.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal position sensor.

In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM determines the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.

A112620E33
0.173,3.81 2.506,4.019 2.333,0.209 10 Accelerator Pedal Sensor 0.759,0.75 1.239,0.932 0.480,0.181 10 Magnet 1.214,1.297 1.741,1.478 0.526,0.181 10 No. 1 IC 1.081,1.02 1.608,1.201 0.526,0.181 10 No. 2 IC 2.067,1.739 2.362,1.921 0.295,0.181 10 VPA 2.067,2.071 2.362,2.252 0.295,0.181 10 EPA 2.067,2.393 2.462,2.574 0.395,0.181 10 VCPA 2.067,2.687 2.439,2.869 0.372,0.181 10 VPA2 2.067,3.005 2.439,3.186 0.372,0.181 10 EPA2 2.067,3.327 2.447,3.508 0.380,0.181 10 VCP2 2.693,1.392 3.018,1.574 0.326,0.181 10 ECM 4.267,1.548 4.423,1.729 0.156,0.181 10 *1 5.864,1.548 6.020,1.729 0.156,0.181 10 *2 3.938,1.842 4.225,2.023 0.287,0.181 10 4.55 3.86,2.047 4.225,2.229 0.365,0.181 10 3.988 3.938,2.253 4.225,2.434 0.287,0.181 10 3.75 3.86,2.458 4.225,2.640 0.365,0.181 10 3.188 3.991,2.823 4.201,3.004 0.210,0.181 10 1.6 3.991,3.042 4.201,3.223 0.210,0.181 10 0.8 4.411,3.346 4.698,3.527 0.287,0.181 10 0.29 4.259,3.596 4.415,3.777 0.156,0.181 10 0 5.784,3.596 6.071,3.777 0.287,0.181 10 15.9 4.682,3.587 5.606,3.827 0.924,0.239 10 Usable Range 4.369,4.054 6.867,4.257 2.498,0.202 10 Accelerator Pedal Angle (°) 4.369,4.391 6.648,4.572 2.279,0.181 10 *1: Accelerator Pedal Fully Released 4.369,4.727 6.756,4.892 2.387,0.165 10 *2: Accelerator Pedal Fully Depressed 4.355,2.014 4.234,1.93 false 4.346,2.182 4.234,2.126 false 4.346,2.228 4.234,2.322 false 4.346,2.397 4.234,2.518 false 4.346,2.901 4.215,2.901 false 4.355,3.116 4.206,3.116 false 0.686,3.387 1.166,3.568 0.480,0.181 10 Magnet 0.843,2.878 0.975,1.099 0.975,1.099 1.062,1.099 false 1.74,0.629 3.947,0.954 2.207,0.325 10 Accelerator Pedal Position Sensor Output Voltage (V) 4.355,1.965 3.925,0.728 false 0.847,2.267 0.649,0.827 0.649,0.827 0.752,0.827 false 1.068,2.561 1.068,1.37 1.068,1.37 1.179,1.37 false 0.843,3.103 0.605,3.461 0.605,3.461 0.679,3.461 false

P2120
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V and VPA2 is more than 2.7 deg, or VPA is higher than 4.8 V.
·

Accelerator pedal position sensor

·

Accelerator pedal assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2122
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V.
(b) VPA2 is more than 2.7 deg.
·

Accelerator pedal position sensor

·

Open in VCPA circuit

·

VPA circuit open or shorted to ground

·

Accelerator pedal assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2123
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Condition (a) continues for 2.0 seconds (1 trip detection logic):
(a) VPA is higher than 4.8 V.
·

Accelerator pedal position sensor

·

Open in EPA circuit

·

Accelerator pedal assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2125
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V and VPA is more than 2.7 deg, or VPA2 is higher than 4.8 V and VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal position sensor

·

Accelerator pedal assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2127
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V.
(b) VPA1 is more than 2.7 deg.
·

Accelerator pedal position sensor

·

Open in VCP2 circuit

·

VPA2 circuit open or shorted to ground

·

Accelerator pedal assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2128
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) VPA2 is higher than 4.8 V.
(b) VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal position sensor

·

Open in EPA2 circuit

·

Accelerator pedal assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



P2138
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


Conditions (a) or (b) continue for 2.0 seconds (1 trip detection logic):
(a) The difference between VPA and VPA2 is less than 0.02 V.
(b) VPA is below 0.4 V and VPA2 is below 1.2 V.
·

VPA and VPA2 circuits are short-circuited

·

Accelerator pedal position sensor

·

Accelerator pedal assembly

·

Accelerator pedal rod (arm) deformed

·

ECM



Related Data List
DTC No. Data List
P2120
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %


P2122
P2123
P2125
P2127
P2128
P2138

WIRING DIAGRAM

A221596E07
0.281,3.198 2.438,3.406 2.156,0.208 10 false Accelerator Pedal Position Sensor 5.604,1.271 6.063,1.479 0.458,0.208 10 false VCPA 5.333,1.198 5.438,1.406 0.104,0.208 10 false 6 5.333,0.354 5.438,0.563 0.104,0.208 10 false 2 5.344,2.458 5.438,2.667 0.094,0.208 10 false 4 5.323,0.771 5.427,0.979 0.104,0.208 10 false 5 5.333,1.615 5.427,1.823 0.094,0.208 10 false 1 5.333,2.031 5.438,2.24 0.104,0.208 10 false 3 5.604,0.427 6,0.635 0.396,0.208 10 false VPA 5.604,0.854 6.052,1.063 0.448,0.208 10 false EPA 5.604,2.521 6.052,2.729 0.448,0.208 10 false VCP2 5.604,1.688 6.042,1.896 0.438,0.208 10 false VPA2 5.604,2.104 6.188,2.313 0.583,0.208 10 false EPA2 1.49,1.365 1.948,1.573 0.458,0.208 10 false VCPA 1.573,0.521 1.885,0.729 0.313,0.208 10 false VPA 1.573,0.948 1.917,1.156 0.344,0.208 10 false EPA 1.5,2.615 1.948,2.823 0.448,0.208 10 false VCP2 1.5,1.792 1.938,2 0.438,0.208 10 false VPA2 1.5,2.208 1.927,2.417 0.427,0.208 10 false EPA2 2,1.281 2.208,1.49 0.208,0.208 10 false 4 1.99,0.438 2.198,0.646 0.208,0.208 10 false 6 1.99,0.865 2.198,1.073 0.208,0.208 10 false 5 2,2.521 2.208,2.729 0.208,0.208 10 false 1 2,1.688 2.208,1.896 0.208,0.208 10 false 3 2,2.104 2.208,2.313 0.208,0.208 10 false 2 5.979,3.052 6.375,3.25 0.396,0.198 10 false ECM 0.281,3.042 0.583,3.229 0.302,0.188 10 false A19 5.24,0.531 5.542,0.708 0.302,0.177 10 false G57 5.24,1.792 5.542,1.969 0.302,0.177 10 false G57 5.229,0.948 5.531,1.125 0.302,0.177 10 false G58 5.24,1.375 5.542,1.552 0.302,0.177 10 false G58 5.24,2.198 5.542,2.375 0.302,0.177 10 false G58 5.25,2.625 5.552,2.802 0.302,0.177 10 false G58

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION)
a.
C129061E03
0.834,1.598 1.046,1.806 0.212,0.208 10 *a 0.266,0.318 0.472,0.524 0.205,0.205 10 *1 2.244,1.598 2.505,1.811 0.261,0.212 10 *b

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.


d.

Read the values.

Standard Voltage:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 8 to 28% 51 to 86%
Depressed 30 to 55% 73 to 98%


Text in Illustration
*1 Accelerator pedal assembly
*a Depressed
*b Released

Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

B

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A19-1 (VCP2) - G58-4 (VCP2) Always Below 1 Ω
A19-2 (EPA2) - G58-3 (EPA2) Always Below 1 Ω
A19-3 (VPA2) - G57-1 (VPA2) Always Below 1 Ω
A19-4 (VCPA) - G58-6 (VCPA) Always Below 1 Ω
A19-5 (EPA) - G58-5 (EPA) Always Below 1 Ω
A19-6 (VPA) - G57-2 (VPA) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A19-1 (VCP2) or G58-4 (VCP2) - Body ground Always 10 kΩ or higher
A19-2 (EPA2) or G58-3 (EPA2) - Body ground Always 10 kΩ or higher
A19-3 (VPA2) or G57-1 (VPA2) - Body ground Always 10 kΩ or higher
A19-4 (VCPA) or G58-6 (VCPA) - Body ground Always 10 kΩ or higher
A19-5 (EPA) or G58-5 (EPA) - Body ground Always 10 kΩ or higher
A19-6 (VPA) or G57-2 (VPA) - Body ground Always 10 kΩ or higher



d.

Reconnect the accelerator pedal position sensor connector.


e.

Reconnect the ECM connector.



OK

3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
a.
U169114E02
1.354,1.115 0.74,1.656 true 1.49,1.135 1.396,1.677 true 1.76,1.135 1.99,1.646 true 1.927,1.125 2.656,1.667 true 1.167,1.698 1.563,1.875 0.396,0.177 10 false EPA2 1.813,1.688 2.208,1.865 0.396,0.177 10 false VCPA 0.438,1.688 0.813,1.865 0.375,0.177 10 false VCP2 0.115,0.115 0.438,0.365 0.323,0.25 10 false *a 2.542,1.688 2.896,1.865 0.354,0.177 10 false EPA 0.469,1 0.75,1.177 0.281,0.177 10 false A19

Disconnect the accelerator pedal position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A19-4 (VCPA) - A19-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A19-1 (VCP2) - A19-2 (EPA2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to accelerator pedal position sensor)


c.

Reconnect the accelerator pedal position sensor connector.



OK

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

5.REPLACE ECM
4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal rod assembly (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off and leave the vehicle for 30 seconds.


d.

Turn the ignition switch to ON.


e.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Confirm that the DTC is not output again.



NEXT

END