Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  U0101  Lost Communication with TCM  


DESCRIPTION

The ECM (engine control unit) communicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).

If there is a problem with this communication, the ECM stores a DTC.

DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Both conditions are met for 1.25 seconds (1 trip detection logic):
·

The battery voltage is 10.5 V or higher.

·

No communication between the ECM and TCM.


·

ECM

·

TCM

·

ECM to TCM circuit



WIRING DIAGRAM

A227728E08
1.094,1.042 2.083,1.24 0.99,0.198 10 false from EFI Fuse 5.792,3.104 6.656,3.49 0.865,0.385 10 false TCM 5.604,2.604 6.208,2.958 0.604,0.354 10 false E1 5.604,1.052 6.146,1.26 0.542,0.208 10 false BATT 5.344,0.865 5.625,1.125 0.281,0.26 10 false 5 5.323,2.417 5.51,2.615 0.188,0.198 10 false 1 5.604,1.563 6.177,1.771 0.573,0.208 10 false CAN+ 5.302,1.375 5.552,1.604 0.25,0.229 10 false 21 5.604,2.083 6.146,2.313 0.542,0.229 10 false CAN- 5.292,1.896 5.552,2.125 0.26,0.229 10 false 20 3.125,1.552 3.625,1.781 0.5,0.229 10 false CAN+ 3.625,1.469 4.156,1.823 0.531,0.354 10 false 24 3.135,2.073 3.635,2.323 0.5,0.25 10 false CAN- 3.615,1.979 4.115,2.302 0.5,0.323 10 false 18 2.99,2.656 3.74,2.99 0.75,0.333 10 false ECM 2.99,2.479 3.729,2.729 0.74,0.25 10 false C92 5.24,1.052 5.698,1.24 0.458,0.188 10 false G70 5.24,2.073 5.75,2.26 0.51,0.188 10 false G70 5.24,1.563 5.802,1.76 0.563,0.198 10 false G70 5.24,2.604 5.708,2.938 0.469,0.333 10 false G69

PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
DTC U0101 is output A
DTC U0101 and other DTCs are output B

HINT:

If any DTCs other than U0101 are output, troubleshoot those DTCs first.




A

2.INSPECT TCM POWER SOURCE CIRCUIT (POWER SOURCE AND BODY GROUND)

B

2.INSPECT TCM POWER SOURCE CIRCUIT (POWER SOURCE AND BODY GROUND)
a.
U170118E02
1.302,1.958 1.427,2.906 true 2.281,1.948 2.188,2.906 true 0.906,0.458 1.229,0.677 0.323,0.219 10 false G69 2.344,0.458 2.698,0.677 0.354,0.219 10 false G70 0.052,0.021 0.25,0.198 0.198,0.177 10 false *a 1.229,2.948 1.719,3.177 0.49,0.229 10 false 1 (E1) 1.896,2.948 2.594,3.146 0.698,0.198 10 false 5 (BATT)

Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G70-5 (BATT) - G69-1 (E1) Ignition switch ON 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to TCM)


c.

Reconnect the TCM connector.



OK

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C92-24 (CAN+) - G70-21 (CAN+) Always Below 1 Ω
C92-18 (CAN-) - G70-20 (CAN-) Always Below 1 Ω
C92-24 (CAN+) or G70-21 (CAN+) - Body ground or other terminals Always 1 MΩ or higher
C92-18 (CAN-) or G70-20 (CAN-) - Body ground or other terminals Always 1 MΩ or higher



d.

Reconnect the TCM connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC U0101 is output B



A

END

B