Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P245C  EGR Cooler Bypass Control Circuit Low  P245D  EGR Cooler Bypass Control Circuit High  


DESCRIPTION

The vacuum switching valve (for EGR bypass valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

P245C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve (for EGR bypass valve) circuit

·

Vacuum switching valve (for EGR bypass valve)

·

ECM



P245D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve (for EGR bypass valve) circuit

·

Vacuum switching valve (for EGR bypass valve)

·

ECM



WIRING DIAGRAM

A221595E12
2.396,1.156 5.469,1.323 3.073,0.167 10 false Vacuum Switching Valve (for EGR Bypass Valve) 2.396,1.01 2.823,1.167 0.427,0.156 10 false C142 1.042,0.938 1.667,1.104 0.625,0.167 10 false EFI No. 2 3.083,2.188 3.354,2.375 0.271,0.188 10 false EFI 3.833,2.698 4.104,2.885 0.271,0.188 10 false EFI 1.146,2.208 1.531,2.396 0.385,0.188 10 false P/I-B 1.458,0.677 1.583,0.844 0.125,0.167 10 false 2 1.063,0.667 1.188,0.833 0.125,0.167 10 false 1 4.594,0.677 4.719,0.844 0.125,0.167 10 false 2 3.594,0.677 3.719,0.844 0.125,0.167 10 false 1 5.188,0.792 5.563,1.01 0.375,0.219 10 false C93 5.188,2.417 5.583,2.635 0.396,0.219 10 false G58 5.531,2.323 6.01,2.542 0.479,0.219 10 false MREL 5.531,0.781 5.969,0.927 0.438,0.146 10 false ECBV 5.281,0.604 5.406,0.771 0.125,0.167 10 false 4 5.229,2.229 5.5,2.438 0.271,0.208 10 false 11 4.469,1.896 4.594,2.063 0.125,0.167 10 false 4 4.479,2.25 4.604,2.417 0.125,0.167 10 false 2 2.698,2.24 2.823,2.406 0.125,0.167 10 false 3 2.688,1.875 2.813,2.042 0.125,0.167 10 false 1 2.646,2.417 2.854,2.573 0.208,0.156 10 false 1B 4.427,2.417 4.646,2.573 0.219,0.156 10 false 1B 4.417,2.063 4.604,2.219 0.188,0.156 10 false 1B 2.646,2.052 2.854,2.208 0.208,0.156 10 false 1C 0.802,2.875 1.281,3.052 0.479,0.177 10 false Battery 5.969,3.375 6.385,3.594 0.417,0.219 10 false ECM 2.792,3.167 4.583,3.594 1.792,0.427 10 false No. 1 Integration Relay (Engine Room Relay Block)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)
a.

Inspect the vacuum switching valve (for EGR bypass valve) (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>VACUUM SWITCHING VALVE>ON-VEHICLE INSPECTION).



OK

2.CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)

NG

5.REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)
2.CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)
a.
U169099E02
0.156,0.146 0.427,0.323 0.271,0.177 10 false *a 0.771,1.333 1.167,1.51 0.396,0.177 10 false C142

Disconnect the vacuum switching valve (for EGR bypass valve) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C142-1 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Vacuum Switching Valve (for EGR Bypass Valve))


c.

Reconnect the vacuum switching valve (for EGR bypass valve) connector.



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)
a.

Disconnect the vacuum switching valve (for EGR bypass valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C142-2 - C93-4 (ECBV) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C142-2 or C93-4 (ECBV) - Body ground Always 10 kΩ or higher



d.

Reconnect the vacuum switching valve (for EGR bypass valve) connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)
a.

Replace the vacuum switching valve (for EGR bypass valve).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the vacuum switching valve (for EGR bypass valve) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve (for EGR bypass valve) and EFI relay (including the EFI No. 2 fuse).




NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch to ON for 3 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Confirm that the DTC is not output again.



NEXT

END