Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P1496  Intake Air Temperature Sensor 1 Circuit Low  P1497  Intake Air Temperature Sensor 1 Circuit High  


DESCRIPTION

A208462E01
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

P1496
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM



P1497
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM



Related Data List
DTC No. Data List
P1496 Intake Air Temp (Turbo)
P1497

HINT:

If DTC P1496 or P1497 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




WIRING DIAGRAM

A210074E16
0.542,2.152 2.964,2.315 2.422,0.163 10 Intake Air Temperature Sensor (Turbo) 5.896,2.407 6.296,2.581 0.400,0.174 10 ECM 6.246,0.206 6.471,0.388 0.225,0.181 10 5 V 5.547,0.644 5.906,0.825 0.358,0.181 10 THIA 5.547,1.252 6.010,1.433 0.463,0.181 10 ETHI 6.159,0.524 6.315,0.706 0.156,0.181 10 R 2.444,1.273 2.563,1.458 0.119,0.185 10 1 2.444,0.66 2.560,0.841 0.115,0.181 10 2 5.362,0.644 5.471,0.801 0.109,0.157 10 3 5.343,1.252 5.464,1.433 0.121,0.181 10 9 5.896,2.263 6.193,2.435 0.297,0.172 10 C90 0.542,1.963 0.832,2.114 0.290,0.151 10 C84

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE [TURBO])
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


d.

Read the value.

OK:

Same as air temperature near intake manifold


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as air temperature near intake manifold) C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
U169130E02
0.646,0.385 0.854,0.563 0.208,0.177 10 false *1 2.635,0.354 2.896,0.552 0.26,0.198 10 false *2 2.385,1.344 2.74,1.51 0.354,0.167 10 false THIA 2.385,1.844 2.729,2.021 0.344,0.177 10 false ETHI 0.854,2.833 1.104,3.083 0.25,0.25 10 false *a 0.625,3.708 0.938,3.865 0.313,0.156 10 false C84

Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


f.

Read the value.

OK:

140°C (284°F) or higher


Text in Illustration
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (Turbo))


g.

Reconnect the intake air temperature sensor (turbo) connector.



OK

7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO).

NG

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C84-2 - C90-3 (THIA) Always Below 1 Ω
C84-1 - C90-9 (ETHI) Always Below 1 Ω



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.



OK

9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A372459E03
2.438,1.021 3.01,1.26 0.573,0.24 10 false THIA 2.438,1.51 2.896,1.708 0.458,0.198 10 false ETHI 2.594,0.229 2.906,0.427 0.313,0.198 10 false *2 0.74,0.417 1.052,0.615 0.313,0.198 10 false *1

Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


e.

Read the value.

OK:

-40°C (-40°F)


Text in Illustration
*1 Intake Air Temperature Sensor (turbo)
*2 ECM


f.

Reconnect the intake air temperature sensor (turbo) connector.



OK

10.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C84-2 or C90-3 (THIA) - Body ground Always 10 kΩ or higher



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.



OK

6.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO).
a.

Replace the intake air temperature sensor (turbo) (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo) (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END