Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the engine switch is turned to on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the engine switch is turned to on (IG), the MIL should be illuminated and should turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A390289E01
2.99,1.198 4.906,1.448 1.917,0.25 10 false Combination Meter Assembly 1.729,1.677 2.5,1.875 0.771,0.198 10 false GAUGE 0.99,3.573 1.76,3.771 0.771,0.198 10 false P/I-B 0.479,4.031 1.25,4.229 0.771,0.198 10 false FL 0.635,4.917 1.406,5.115 0.771,0.198 10 false Battery 5.635,4.646 6.885,5.031 1.25,0.385 10 false Power Management Control ECU 2.583,4.729 4.635,5 2.052,0.271 10 false No. 1 Integration Relay 6.125,2.844 6.583,3.042 0.458,0.198 10 false G184 5.719,3.969 6.177,4.167 0.458,0.198 10 false IG2D 5.542,4.094 5.698,4.292 0.156,0.198 10 false 8 5.635,4.469 6.094,4.667 0.458,0.198 10 false G50 6.135,3.031 6.594,3.229 0.458,0.198 10 false ECM 5.396,0.792 5.552,0.99 0.156,0.198 10 false 7 4.75,0.438 4.906,0.635 0.156,0.198 10 false 7 2.875,0.448 3.177,0.646 0.302,0.198 10 false 28 5.625,0.51 5.917,0.708 0.292,0.198 10 false W 2.875,0.646 3.167,0.844 0.292,0.198 10 false G6 4.698,0.656 4.99,0.854 0.292,0.198 10 false G7 4.302,0.833 4.594,1.031 0.292,0.198 10 false CHK 3.198,0.76 3.49,0.958 0.292,0.198 10 false IG+ 2.031,3.406 2.344,3.604 0.313,0.198 10 false 1C 2.031,3.969 2.344,4.167 0.313,0.198 10 false 1J 4.438,3.115 4.75,3.313 0.313,0.198 10 false 1J 4.677,3.979 4.99,4.177 0.313,0.198 10 false 1J 2.76,3.563 3.073,3.76 0.313,0.198 10 false IG2 3.594,4.198 3.906,4.396 0.313,0.198 10 false IG2 2.042,3.24 2.198,3.438 0.156,0.198 10 false 1 2.063,3.781 2.219,3.979 0.156,0.198 10 false 3 4.219,3.135 4.375,3.333 0.156,0.198 10 false 7 4.708,3.792 4.865,3.99 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Turn the engine switch on (IG).


b.

Check the illumination condition of the MIL.

Result
Result Proceed to
MIL remains on A
MIL does not illuminate B
Illuminates → Turns off C



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT ENGINE STARTS

C

2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result
Result Proceed to
DTC is not output A
Any DTCs is output B

HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check that the MIL is not illuminated.


Result
Result Proceed to
MIL remains on A
MIL does not illuminate B

d.

Reconnect the ECM connector.



A

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (CHK) or G184-7 (W) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT ENGINE STARTS
a.

Turn the engine switch on (IG).


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start B



A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (CHK) - G184-7 (W) Always Below 1 Ω



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR