The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.
When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Check that the Malfunction Indicator Lamp (MIL) lights up when the engine switch is turned on (IG).
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Check the communication between the GTS and ECM.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
(See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>MIL Circuit)
Disconnect the diesel throttle body assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the diesel throttle body assembly connector.
A
B
Disconnect the accelerator pedal position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the accelerator pedal position sensor connector.
A
B
Disconnect the fuel pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the fuel pressure sensor connector.
A
B
Disconnect the manifold absolute pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the manifold absolute pressure sensor connector.
A
B
Disconnect the electric EGR control valve assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the electric EGR control valve assembly connector.
A
B
Disconnect the differential pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the differential pressure sensor connector.
A
B
Disconnect the nozzle vane position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the nozzle vane position sensor connector.
A
B
(See pageEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY)
Disconnect the mass air flow meter sub-assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the mass air flow meter sub-assembly connector.
A
B
Disconnect the camshaft position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the camshaft position sensor connector.
A
B
Disconnect the crankshaft position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the crankshaft position sensor connector.
A
B
Disconnect the diesel throttle body assembly connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the electric EGR control valve assembly connector.
Disconnect the differential pressure sensor connector.
Disconnect the nozzle vane position sensor connector.
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the camshaft position sensor connector.
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C151-29 (VCVL) - Body ground and other terminals | Always | 10 kΩ or higher |
| G185-29 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| G185-30 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C151-28 (VCM) - Body ground and other terminals | Always | 10 kΩ or higher |
| C149-28 (VCPM) - Body ground and other terminals | Always | 10 kΩ or higher |
| C151-31 (VCEG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C151-32 (VCPX) - Body ground and other terminals | Always | 10 kΩ or higher |
| C151-30 (VNVC) - Body ground and other terminals | Always | 10 kΩ or higher |
| C150-25 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C152-17 (VCG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C152-20 (VCNE) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the diesel throttle body assembly connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the electric EGR control valve assembly connector.
Reconnect the differential pressure sensor connector.
Reconnect the nozzle vane position sensor connector.
Reconnect the mass air flow meter sub-assembly connector.
Reconnect the camshaft position sensor connector.
Reconnect the crankshaft position sensor connector.
Reconnect the ECM connectors.
OK
NG