The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.
When the throttle valve is fully closed, a voltage of approximately 0.4 to 1.0 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.6 to 4.2 V when the throttle valve is fully opened.
The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 3 seconds or more | Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic). | ·
Throttle position sensor ·
Open or short in VLU circuit ·
Open in VCVL circuit ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 3 seconds or more | Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic). | ·
Throttle position sensor ·
Open in EVLU circuit ·
VCVL and VLU circuits are short-circuited ·
ECM |
If DTC P0122 and/or P0123 is stored, the following symptoms may appear:
- Intake booming noise
- Black smoke
- Lack of power
- Vibration at engine stop
- Turbo overspeed, turbo damage
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C151-29 (VCVL) - C151-20 (EVLU) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C151-21 (VLU) - C151-20 (EVLU) | Engine switch on (IG) | 3.6 to 4.2 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P0122 or P0123 is output | B |
A
B
Disconnect the diesel throttle body assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| r5-5 (VC) - r5-3 (E2) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector
(to Diesel Throttle Body Assembly) |
Reconnect the throttle position sensor connector.
OK
NG
Disconnect the diesel throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r5-6 (VTA) - C151-21 (VLU) | Always | Below 1 Ω |
| r5-3 (E2) - C151-20 (EVLU) | Always | Below 1 Ω |
| r5-6 (VTA) or C151-21 (VLU) - Body ground and other terminals | Always | 10 kΩ or higher |
| r5-3 (E2) or C151-20 (EVLU) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the diesel throttle body assembly connector.
Reconnect the ECM connector.
OK
NG
Disconnect the diesel throttle body assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| r5-5 (VC) - r5-6 (VTA) | Engine switch off | No short or open |
| r5-6 (VTA) - r5-3 (E2) |
| *a | Front view of wire harness connector
(to Diesel Throttle Body Assembly) |
Reconnect the diesel throttle body assembly connector.
OK
NG
Replace the diesel throttle body assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).
NEXT
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT