Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate and Magneto Resistance Element (MRE) type sensor. The crank angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.

P0335
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Crank or start engine Either of the following conditions is met (1 trip detection logic):
·

No crankshaft position sensor signal to the ECM while cranking.

·

No crankshaft position sensor signal to the ECM while engine running.


·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM



P0339
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine running at 1000 rpm or more with vehicle stationary Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):

(a) Engine speed is 1000 rpm or more.

(b) Starter signal is off.

(c) 3 seconds or more have elapsed since the starter signal switched from on to off.


·

Crankshaft position sensor

·

Crankshaft (crank angle sensor plate)

·

ECM



Related Data List
DTC No. Data List
P0335
P0339
Engine Speed

HINT:
·

If DTC P0335 and/or P0339 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power



·
A340471E03
0.021,0.813 0.25,0.979 0.229,0.167 10 false G2 3,1.021 3.344,1.188 0.344,0.167 10 false GND 1.052,1.865 2.021,2.031 0.969,0.167 10 false 20 msec./DIV. 2.615,0.156 3.177,0.323 0.563,0.167 10 false 2 V/DIV. 3,1.542 3.344,1.708 0.344,0.167 10 false GND 0.021,1.344 0.25,1.51 0.229,0.167 10 false NE

Reference: Inspection using an oscilloscope.

The correct waveform is as shown.

ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine



MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

A348539E12
0.51,2.229 2.719,2.427 2.208,0.198 10 false Crankshaft Position Sensor 0.521,2.042 0.979,2.24 0.458,0.198 10 false r7 1.521,0.469 1.979,0.667 0.458,0.198 10 false VC 1.448,1.042 1.906,1.24 0.458,0.198 10 false NE+ 1.49,1.583 1.948,1.781 0.458,0.198 10 false NE- 5.656,0.469 6.313,0.667 0.656,0.198 10 false VCNE 5.667,1.021 6.125,1.219 0.458,0.198 10 false NE+ 5.646,1.583 6.104,1.781 0.458,0.198 10 false NE- 1.833,0.573 2.292,0.771 0.458,0.198 10 false 3 1.833,1.156 2.292,1.354 0.458,0.198 10 false 1 1.823,1.698 2.281,1.896 0.458,0.198 10 false 2 5.406,0.583 5.667,0.792 0.26,0.208 10 false 20 5.385,1.146 5.875,1.333 0.49,0.188 10 false 28 5.396,1.698 5.677,1.896 0.281,0.198 10 false 19 5.979,2.229 6.51,2.427 0.531,0.198 10 false ECM 5.99,2.042 6.448,2.24 0.458,0.198 10 false C152

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Start the engine.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor.

Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ENGINE
a.

Check the engine cranking condition.

Result:
Result Proceed to
Cranking is OK. A
Does not crank at all* B


*: When the engine cannot crank, there may be a malfunction in the starter assembly.



A

2.READ VALUE USING GTS (ENGINE SPEED)

B

GO TO PROBLEM SYMPTOMS TABLE (ENGINE DOES NOT CRANK (DOES NOT START))

2.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.


d.

Start the engine.


e.

Read the values displayed on the GTS while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.





OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0339)

NG

4.INSPECT ECM TERMINAL VOLTAGE (CRANKSHAFT POSITION SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0339)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Start the engine and run it at 1000 rpm or higher for 5 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0335 and/or P0339 is output B



B

4.INSPECT ECM TERMINAL VOLTAGE (CRANKSHAFT POSITION SENSOR)

A

4.INSPECT ECM TERMINAL VOLTAGE (CRANKSHAFT POSITION SENSOR)
a.

Inspect the ECM using an oscilloscope.

i.

While the engine is idling, check the waveform between the terminals of the ECM connector.



U169467E01
5.854,0.896 5.51,1.385 false 5.896,0.938 6.219,1.406 false 0.104,0.979 0.344,1.146 0.24,0.167 10 false NE 3.51,1.083 3.885,1.25 0.375,0.167 10 false GND 1.417,1.427 2.396,1.604 0.979,0.177 10 false 50 msec./DIV. 2.833,0.01 3.417,0.188 0.583,0.177 10 false 2 V/DIV. 5.604,0.24 6,0.396 0.396,0.156 10 false C152 5.156,1.417 5.833,1.583 0.677,0.167 10 false 19 (NE-) 5.927,1.417 6.521,1.583 0.594,0.167 10 false 28 (NE+) 4.104,0.031 4.479,0.198 0.375,0.167 10 false *a

Text in Illustration
*a Component with harness connected
(ECM)
- -

OK:
Tester Connection Tester Range Condition Specified Condition
C152-28 (NE+) - C152-19 (NE-) 2 V/DIV.
50 msec./DIV.
Cranking to idling Correct waveform as shown in illustration



NG

5.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

OK

10.REPLACE ECM
5.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A316078E03
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG

Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.


Text in Illustration
*a Clearance



OK

6.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)

NG

9.SECURELY REINSTALL CRANKSHAFT POSITION SENSOR
6.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the crank angle sensor plate.

OK:

Crank angle sensor plate does not have any cranks or deformation.




OK

7.REPLACE CRANKSHAFT POSITION SENSOR

NG

8.REPLACE CRANKSHAFT
7.REPLACE CRANKSHAFT POSITION SENSOR
a.


NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE CRANKSHAFT

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.SECURELY REINSTALL CRANKSHAFT POSITION SENSOR
a.

Securely reinstall the crankshaft position sensor (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSTALLATION).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off for 30 seconds or more.


e.

Start the engine and run it at 1000 rpm or higher for 5 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END