| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idling for 1 second or more | Even though the CPU (command area inside the ECU) is outputting the pre-stroke control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic). | ·
Open or short in pre-stroke control valve circuit ·
Fuel supply pump assembly ·
ECM |
| DTC No. | Data List |
|---|---|
| P0627 | ·
Common Rail Pressure ·
Target Common Rail Pressure |
For more information on the fuel supply pump assembly (pre-stroke control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DIAGRAM).
When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Common Rail Pressure.
Under a stable operating condition such as idling, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the pre-stroke control valve (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>INSPECTION).
OK
NG
Disconnect the pre-stroke control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| r6-1 - C150-3 (PCV+) | Always | Below 1 Ω |
| r6-2 - C150-4 (PCV-) | Always | Below 1 Ω |
| r6-1 (+B) or C150-3 (PCV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| r6-2 (PCV) or C150-4 (PCV-) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the pre-stroke control valve connector.
Reconnect the ECM connector.
OK
NG
Connect the GTS to the DLC3
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| DTC P0627 is output | B |
A
B
Replace the fuel supply pump assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
NEXT
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT